2010 Mazda MAZDA3
Problems, recalls and owner-reported issues
Structure is the leading concern among 686 owner complaints filed for this model year. This is the highest complaint count among 22 MAZDA3 model years with reports.
Of the 2010 reports, 18 involved a crash and 5 involved a fire. 13 people were injured.
What owners report most often
Recalls and investigations
SeatsFeb 9, 2017
Mazda North American Operations (Mazda) is recalling certain 2011 Mazda2 and 2010-2011 Mazda3 and Mazdaspeed3 vehicles equipped with a manual seat lifter. In the affected vehicles, the seat height adjustment lifter links may break or detach from the seat frame and the seat angle may incline causing the driver to not be able to maintain an appropriate driving position.
If the driver cannot maintain an appropriate driving position, there is an increased risk of a crash.
Mazda will notify owners, and dealers will inspect the seat lifter links and install a reinforcement bracket to the lifter links, or replace the entire seat adjuster unit, free of charge. The recall began April 7, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 0917B.
Campaign 17V082000 on NHTSA.gov
Structure, body, hatchback/liftgateSep 6, 2016
Mazda North American Operations (Mazda) is recalling certain model year 2010-2013 Mazda3 and Mazdaspeed3 vehicles manufactured November 18, 2008, to June 8, 2013, 2012-2015 Mazda5 vehicles manufactured October 26, 2010, to June 22, 2015, 2016 CX-3 vehicles manufactured June 1, 2015, to December 26, 2015, and 2013-2016 CX-5 vehicles manufactured December 15, 2011, to December 26, 2015. On the affected vehicles, the lift gate support struts may corrode, possibly causing the struts to break and/or the lift gate to drop unexpectedly.
If the lift gate falls unexpectedly, it may hit the user, increasing their risk of injury.
Mazda dealers will replace the both lift gate supports, free of charge, however parts are not currently available. The recall began April 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9916H.
Campaign 16V644000 on NHTSA.gov
Electrical systemApr 16, 2009
MAZDA IS RECALLING 25,400 MY 2010 MAZDA3 VEHICLES. A CLEARANCE BETWEEN THE ENGINE HARNESS AND THE HOUSING OF STARTER MOTOR MAY BE INSUFFICIENT. DUE TO THIS, THE COVERING OF THE HARNESS MAY BE DAMAGED THROUGH VIBRATION DURING OPERATION POSSIBLY CAUSING A SHORT-CIRCUIT BETWEEN CERTAIN HARNESS WIRES AND THE STARTER HOUSING. A SHORT-CIRCUIT CAN RESULT IN ENGINE CONTROL MALFUNCTION AND/OR POOR SHIFT QUALITY.
THE MAIN FUSE MAY BLOW OUT CAUSING THE ENGINE TO STALL AND INABILITY OF RESTART, INCREASING THE RISK OF A CRASH.
DEALERS WILL HAVE THE ENGINE HARNESS INSPECT AND ADD A PROTECTOR CLIP ON THE AFFECTED SECTION OF THE HARNESS. IF NECESSARY, THE HARNESS WILL BE REPAIRED. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON MAY 6, 2009. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500.
Campaign 09V126000 on NHTSA.gov
Representative owner complaints: wheels
54 reports, newest first. Show all
Tires, Wheels, Dec 30, 2012
SPONTANEOUS FAILURE OF TIRE VALVE STEM RESULTING IN THE NEAR INSTANTANEOUS DECOMPRESSION OF THE REAR DRIVER'S SIDE TIRE. AT THE TIME I WAS ATTEMPTING TO CHECK THE TIRE PRESSURE OF THAT WHEEL. THE STEM SEPARATED INTO TWO PIECES WITHOUT ANY PRIOR INDICATION OF WEAR. *TR
Tires, Wheels, Dec 10, 2011
THE VALVE STEM OF MY TIRE PRESSURE MONITORING SYSTEM (TPMS) HAD SIGNIFICANT CORROSION LEADING TO IMMEDIATE AND RAPID DEFLATION OF FRONT LEFT TIRE WHILE REMOVING AIR HOSE WHILE TENDING TO TPMS WARNING LIGHT. THE RAPID DEFLATION WAS DUE TO COMPLETE AND IMMEDIATE SEVERANCE WHERE THE THREADED PORTION OF VALVE STEM MET VALVE CAP WITHOUT ANY TORQUE OR ABNORMAL PRESSURE APPLIED. THE SEVERED EDGE OF THE VALVE STEM SHOWS CLEAR EVIDENCE OF CORROSION 360 DEGREES AND INWARD, WITH A THIN HALO (APPX. 1/10 OF THE WALL) REMAINING. BOTH THE TIRE AND VALVE STEM SHOWED NO SIGN OF LEAKING AND HELD PROPER PRESSURE WHILE FILLING TO RECOMMENDED PRESSURE UNTIL REMOVAL OF AIR HOSE CAUSED THE STEM TO SPLIT HORIZONTALLY BETWEEN THE 9TH AND 10TH THREAD. PLASTIC VALVE CAPS WERE IN PLACE ON ALL 4 TIRES. SPARE TIRE ALSO NOT ABLE TO BE PUT IN PLACE DUE TO 'STUCK' LUG NUTS ON SAME TIRE; SIMILAR CORROSION IS SUSPECT, POSSIBLY CAUSED BY GALVANIC CORROSION DUE TO METALS FOUND IN DISK BRAKES, SHOES OR ALLOY RIM. VEHICLE IS STILL UNDER WARRANTY AND NEEDED TOW TO NEAREST MAZDA DEALERSHIP FOR REPAIR. WHEN CALLING THE SERVICE DEPARTMENT ABOUT SENDING MY VEHICLE OVER I ADDRESSED MY CONCERNS ABOUT THE OTHER 3 VALVE STEMS NEEDING REPLACEMENT AND WAS TOLD "THEY ARE $150 EACH SO IF YOU WANT TO PAY TO HAVE THE OTHER ONES REPLACED YOU CAN, BUT THE DEALERSHIP ISN'T GOING TO PAY FOR IT" MY RESPONSE: "REALLY? I'M THANKFUL THIS DIDN'T HAPPEN ON THE HIGHWAY, I WOULD HOPE THE SAFETY OF YOUR CUSTOMERS WOULD COME FIRST" ..NO IM SORRY, NO WE'LL LOOK INTO IT FOR YOU, JUST "WELL CAN I GIVE YOU THE NUMBER FOR ROADSIDE ASSISTANCE?" *TR
Tires, Wheels, Nov 12, 2011
THE TIRE PRESSURE WARNING LIGHT CAME OUT ONE WEEK AFTER PURCHASING MY NEW MAZDA 3 IN JULY 2010. I FILLED THE TIRE WITH AIR BUT LIGHT WOULD COME BACK ON SEVERAL WEEKS LATER. TOOK THE CAR TO DEALER IN OCTOBER 2010 AND THEY COULDN'T FIND ANY PROBLEMS. TOOK IT BACK TO DEALER IN OCTOBER 2011 AND NOW THEY FIND A BENT WHEEL RIM. REPLACED THE RIM AT MY COST -- OVER 350.00. 4 WEEKS LATER, WARNING LIGHT COMES BACK ON. I CHECKED THE AIR ON ALL TIRES AND THEY ARE FINE. MY MAZDA HAS ONLY 6,000 MILES ON IT. MAZDA CANNOT SEEM TO FIX THE WARNING LIGHT PROBLEM AND THEY BLAME IT ON CHANGE IN WEATHER TEMPERATURE! COMPLAINED TO THE DEALER AND THEY SAY TO BRING THE CAR BACK IN. I REFUSE TO PAY A DIAGNOSTIC FEE WHEN THIS IS CLEARLY A MAZDA PROBLEM AND THE CAR IS UNDER WARRANTY. I'VE OWNED MAZDA CARS SINCE 1993; THIS IS MY 6TH MAZDA AND I AM VERY UPSET. *TR
Wheels, Jun 17, 2011
THERE HAS NOT BEEN A FAILURE TO DATE, HOWEVER, ADDING MY VEHICLE TO THE OTHER MAZDA3'S IN THE DATA BASE WHERE THE DESIGN OF THE VEHICLE IS CREATING UNEVEN TIRE WEAR. AS I HAVE READ IN NO LESS THAN 5 BLOGS, THE MANUFACTURER INTENTIONALLY CAMBERS THE REAR TIRES TO INCREASE THE PERFORMANCE AND HANDLING AND UPON NORMAL ROTATION OF THE TIRES, A "BUMPING" NOISE CAN BE HEARD AND FELT. THE TIRE MANUFACTURER WILL DO NOTHING AND STATES IS A DESIGN ISSUE AND MAZDA STATES I MUST DEAL WITH THE TIRE MANUFACTURER. THIS UNEVEN TIRE WEAR AND VIBRATION COULD LEAD TO ADDITIONAL TIRE WEAR AS NOTED BY OTHER OWNERS. AT 11,000 MILES, I SHOULD NOT BE FACED WITH REPLACING THE TIRES.