2008 Toyota Highlander
Problems, recalls and owner-reported issues
Service brakes is the leading concern among 404 owner complaints filed for this model year. This is the 3rd highest complaint count among 25 Highlander model years with reports.
Of the 2008 reports, 44 involved a crash and 14 involved a fire. 42 people were injured and 2 people died.
What owners report most often
Recalls and investigations
Seats, front assembly, seat heater/coolerJun 2, 2016
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.
If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Campaign 16V396000 on NHTSA.gov
Visibility, power window devices and controlsOct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Campaign 15V689000 on NHTSA.gov
Seats, front assembly, seat heater/coolerNov 19, 2014
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.
Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
Campaign 14V743000 on NHTSA.gov
Air bags, frontal, driver side, inflator moduleApr 9, 2014
Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned.
If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
Campaign 14V168000 on NHTSA.gov
Visibility, power window devices and controlsOct 10, 2012
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
If the switch overheats, it may melt, possibly resulting in a fire.
Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
Campaign 12V491000 on NHTSA.gov
Air bagsApr 21, 2011
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Campaign 11V245000 on NHTSA.gov
Equipment, other, labelsFeb 3, 2010
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
Campaign 10V036000 on NHTSA.gov
Equipment, other, labelsFeb 3, 2010
GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
THIS DOES NOT MEET THE STANDARD REQUIREMENTS.
DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
Campaign 10V035000 on NHTSA.gov
Vehicle speed control, accelerator pedalJan 27, 2010
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008-2010 HIGHLANDER, MODEL YEAR 2009-2010 COROLLA, VENZA AND MATRIX PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT. THIS RECALL IS AN EXPANSION OF A CAMPAIGN OF 3.8 MILLION OTHER TOYOTA VEHICLES ANNOUNCED IN 2009 FOR THE SAME ISSUE (SEE 09V-388).
A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
TOYOTA WILL MODIFY OR REPLACE THE ACCELERATOR PEDALS ON THE SUBJECT VEHICLES. FLOOR SURFACE MODIFICATIONS ARE ALSO BEING CONSIDERED AND WILL BE INCLUDED FOR ANY MODEL FOR WHICH IT IS DEEMED APPROPRIATE. INITIALLY, DEALERS WILL BE INSTRUCTED ON HOW TO RESHAPE THE ACCELERATOR PEDAL FOR THE REPAIR. AS REPLACEMENT PARTS WITH THE SAME SHAPE AS THE MODIFIED PEDAL BECOME AVAILABLE, THEY WILL BE MADE AVAILABLE TO THE DEALERS FOR THE REPAIR. CUSTOMERS WHO HAVE HAD THE PEDAL RESHAPE REMEDY COMPLETED WILL HAVE THE OPPORTUNITY TO RECEIVE A NEW PEDAL IF THEY DESIRE, AFTER REPLACEMENT PEDALS BECOME AVAILABLE. IN ADDITION, TOYOTA WILL REPLACE ANY TOYOTA ALL-WEATHER FLOOR MAT IN A SUBJECT VEHICLE WITH A NEWLY DESIGNED MAT, FREE OF CHARGE. FOR THOSE CUSTOMERS WHO HAVE THE PREVIOUS DESIGN ALL-WEATHER FLOOR MAT BUT DO NOT NEED OR WANT THE NEWLY DESIGNED ALL-WEATHER FLOOR MAT, TOYOTA WILL RECOVER THE PREVIOUS DESIGN ALL-WEATHER FLOOR MAT AND REIMBURSE ITS PRICE. THE SAFETY RECALL BEGAN MARCH 30, 2010. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Campaign 10V023000 on NHTSA.gov
Equipment, other, labelsJun 15, 2009
TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."
INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
Campaign 09V223000 on NHTSA.gov
EquipmentMay 14, 2009
SOUTHEAST TOYOTA IS RECALLING 3,499 STAINLESS STEEL EXHAUST TIPS SOLD BY SOUTHEAST TOYOTA AS AN OPTIONAL ACCESSORY FOR USE ON MY 2008 HIGHLANDER AND HIGHLANDER HYBIRD VEHICLES. DUE TO IMPROPER HEAT TREATMENT DURING THE MANUFACTURING PROCESS, THE ORIGINAL CLAMP USED TO SECURE THE STAINLESS STEEL EXHAUST TIP TO THE EXHAUST PIPE MAY DEVELOP MICROSCOPIC CRACKS. EVENTUALLY THE CRACK MAY EXPAND CAUSING THE CLAMP TO BREAK.
THE ORIGINAL CLAMP AND THE TOYOTA STAINLESS STEEL EXHAUST TIP MAY FALL OFF THE VEHICLE'S EXHAUST PIPE AND BECOME A ROAD HAZARD WHICH WOULD INCREASE THE RISK OF A VEHICLE CRASH.
SOUTHEAST TOYOTA WILL NOTIFY OWNERS AND REPLACE THE CLAMP FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING MAY/JUNE 2009. OWNERS MAY CONTACT SOUTHEAST TOYOTA CUSTOMER LOYALTY DEPARTMENT AT 1-800-301-6859.
Campaign 09E028000 on NHTSA.gov
EquipmentApr 27, 2009
TOYOTA IS RECALLING 39,100 STAINLESS STEEL EXHAUST TIPS SOLD BY TOYOTA AS AN OPTIONAL ACCESSORY FOR USE ON MY 2008 HIGHLANDER AND HIGHLANDER HYBRID VEHICLES. DUE TO IMPROPER HEAT TREATMENT DURING THE MANUFACTURING PROCESS, THE ORIGINAL CLAMP USED TO SECURE THE TOYOTA STAINLESS STEEL EXHAUST TIP TO THE EXHAUST PIPE MAY DEVELOP MICROSCOPIC CRACKS. EVENTUALLY THE CRACK MAY EXPAND CAUSING THE CLAMP TO BREAK.
THE ORIGINAL CLAMP AND THE TOYOTA STAINLESS STEEL EXHAUST TIP MAY FALL OFF THE VEHICLE'S EXHAUST PIPE AND BECOME A ROAD HAZARD WHICH WOULD INCREASE THE RISK OF A VEHICLE CRASH.
TOYOTA WILL NOTIFY OWNERS AND REPLACE THE CLAMP FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 4, 2009. OWNERS MAY CONTACT TOYOTA CUSTOMER EXPERIENCE CENTER AT 1 888-270-9371 MONDAY THROUGH FRIDAY, 5:00 AM TO 6:00 PM, SATURDAY 7:00 AM THROUGH 4:00 PM PACIFIC TIME.
Campaign 09E022000 on NHTSA.gov
Seat belts, rear/otherApr 18, 2008
TOYOTA IS RECALLING 90,189 MY 2008 HIGHLANDER AND HIGHLANDER HYBRID PASSENGER VEHICLES EQUIPPED WITH A THIRD ROW SEAT. THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE NON-DRIVER DESIGNATED SEATING POSITIONS (DSP) ON THESE VEHICLES IS EQUIPPED WITH SEAT BELT ASSEMBLIES THAT HAVE A FEATURE THAT CONVERTS THE RETRACTOR FROM AN EMERGENCY LOCKING RETRACTOR (ELR) TO AN AUTOMATIC LOCKING RETRACTOR (ALR). THE BELTS CONVERT TO THE ALR MODE AFTER THE WEBBING HAS BEEN FULLY WITHDRAWN FROM THE RETRACTOR. THE SYSTEM IS DESIGNED SO THAT AS THE BELT IS RELEASED INTO THE RETRACTOR, THE SYSTEM REMAINS IN THE ALR MODE SO THAT A CHILD RESTRAINT SYSTEM (CRS) CAN BE TIGHTLY SECURED.
HOWEVER, FOR THE TWO THIRD ROW DSP'S ON THESE VEHICLES, THE ALR MODE DEACTIVATES BEFORE THE WEBBING IS FULLY RETRACTED, SO THAT IT WILL NOT LOCK WHEN CERTAIN REAR-FACING CRS'S THAT HAVE A SHORT SEAT BELT ROUTING PATH ARE INSTALLED IN THE VEHICLE. THIS CAN ALLOW THE SEAT BELT WEBBING TO SPOOL OUT DURING NORMAL DRIVING MANEUVERS, WHICH COULD AFFECT THE STABILITY OF A CHILD RESTRAINT INSTALLED AT THOSE SEATING POSITIONS. AS SUCH, THIS COULD DISCOURAGE THE USE OF A CHILD RESTRAINT AND IN THE EVENT OF A CRASH, THE CHILD MAY NOT BE ADEQUATELY PROTECTED POSSIBLY RESULTING IN INJURY.
DEALERS WILL INSTALL A NEWLY DESIGNED SEAT BELT COMPONENT FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR ABOUT DECEMBER 18, 2008. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Campaign 08V181000 on NHTSA.gov
Representative owner complaints
404 reports, newest first.
Service brakes, Hydraulic, Parking brake, Feb 21, 2023
The contact owns a 2008 Toyota Highlander. The contact stated while driving at an undisclosed speed, the ABS and stabili-trak warning lights were illuminated. The vehicle was taken to an independent mechanic to be diagnosed. The mechanic retrieved DTC: C1391, indicating that the brake actuator assembly was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and the contact was informed that the Extended Program had expired, and the contact was advised to call the NHTSA Hotline for assistance. The failure mileage was approximately 180,000.
Seat belts, Feb 1, 2023
Unable to buckle 3rd row passenger side seat belt buckle. Safety of my children were put at risk as I didn’t realize this until recently since our family grew. No warning indicating lights are on.
Air bags, Dec 6, 2022, crash
Airbag failed to deploy in a front-left collision with another vehicle. The other vehicle's airbags did deploy. The vehicle is totalled and not available for inspection. The lack of deployment resulted in a head injury and whiplash. There was no advanced warning of this being a problem.
Service brakes, Nov 3, 2022
All the lights relating to brakes and ABS flashed up on the dashboard. We continued home slowly. Upon investigation from a trusted mechanic it seems it is the brake actuator. From numerous reviews and complaints online this is a reoccurring issue with Toyota cars but recalls were only issued for 2006-2007 models even though the 2008 Highlander hybrids use the same part.
Structure, Oct 19, 2022
While driving the vehicle the back door and glass back panel sometimes release and open unexpectedly . I saw that a "service bulletin" was issued for a problem with the rear door, (T-SB-0091-12), but a dealership told me my vehicle wasn't "covered".
Service brakes, Sep 22, 2022
Needed to have hub and bearing and spindles replaced in front driver's side wheel (AWD). Repair shop completed repairs and aligned the vehicle. Computer needed to be reset after alignment. Shop followed reset instructions and vehicle then showed codes for the ABS system (ABS pump and actuator and skid control module). Repair shop cannot reset computer without replacing parts estimated cost is over $5,600. No work on brakes or ABS system was done. No errors or codes previously existed prior to replacement of bearing and hub. No codes existed until after the alignment was completed. ABS system no longer works. Repair was completed at an independent repair shop. Have appointment with dealership on 9/29 to see if code can be reset. These codes were an issue in 06-07 Highlander hybrids and Prius models and part of a recall.
Service brakes, Aug 19, 2022
ABS warning light at 118,000 7/8/2022 C1391 This is a known recall and problem on the earlier model Highlanders, as well as the second generation Highlanders, but not recalled as of today 8/19/22. It is a flawed ABS design and safety hazzard.
Service brakes, Aug 10, 2022
Brake system failed in hybrid and issue is well documented. Current lawsuits however not including this make/model.
Vehicle speed control, Aug 5, 2022, crash
Slowing down, but the car surged forward colliding into a building. The dealership only ran a .5 hour diagnosis and couldn't find anything. Did not proceed w/further diagnosis as did not want to pay out of pocket.
Wheels, Service brakes, Fuel/propulsion system, Jul 24, 2022
No nothing has been inspected I didn’t even know it had a recall all my lights on my truck are on now
Electrical system, Other or unspecified, Jun 13, 2022
This vehicle has had ongoing issues with the O2 sensors not working, I have researched online for years and have read that there are several online forums of 2008 Highlander owners complaining of the same issue. The problem that I (we all) face with this, is that it constantly fails, never being able to know if there is an actual issue becuase of the faulty sensors or wiring causing the sensors to go out. I am always frightened that something is wrong with the car and spent hundreds and continue to spend having my car checked. I am a single mom who lost my job at the beginning of the pandemic, I have two school aged kids. Having them in a car that I can not be sure we are safe in, is scary. The cost to replace the sensors as there are 3 that have been a constant pain of not working correctly is insane! It is going to be in upwards of $600 to repair! I absolutely can't afford that, being an unemployed single mother of two. Even when I was employed, living paycheck to paycheck to have to pay out almost a thousand dollars when from what I've read from others that replacing will still result in it failing again. So I have to drive around in a car that has all the sensor lights on, something really bad could happen to the car and since all the sensor lights remain on, I'll never know if something is wrong with the car- something bad could happen to me and my children while we are driving in the car. How can someone replace the sensors only for them to keep going out. This is a serious problem, I've dealt with this for years, only today did I learn that I could report this after receiving a recall letter from Toyota today regarding the paint on my car.
Electrical system, Service brakes, Apr 5, 2022, crash
ABS system failure for the second time after repair, cost $3400 to replace after causing complete loss of brakes. 4 years after incident same exact ABS warning and VCS system failure with message to immediately take vehicle to dealership. There is a class action lawsuit on other hybrid models but Toyota inspected and said it would cost another $3500 to fix because there is no recall on the part.
Service brakes, Apr 2, 2022
Chief complaint ISSUES were as follow : " BRAKE MALFUNCTION STOP The vehicle in a safe plase immediately and contact Dealer." Warning lights were illuminated on the instrument cluster or information display: yellow master warning light, the red brake system warning light and buzzer, yellow ABS warning light, yellow SLIP indicator light. After carefull diagnosis, it was determined that the brake booster pump was turning on frequently or working constantly. Unusual squeaky noise can be heard when depressing the brake pedal. In addition, the ABS Diagnostic Trouble Codes were identical as the problem. From research it should be noted. Toyota has previously identified and issued safety recall for the same vehicle however stopped short of including the 2008 Toyota Highlander hybrid model with the aforementioned Vin number.
Other or unspecified, Mar 11, 2022
The drivers door either locks or doesn’t when hitting the lock button it shake (unlocks an locks rapidly.
Other or unspecified, Mar 5, 2022
The driver door lock either won’t unlock or won’t lock it does a back n forth montion
Equipment, Mar 5, 2022
The radio started skipping and the DVD player won’t turn on
Service brakes, Feb 27, 2022
When I started my 2008 Highlander Hybrid on Valentine’s Day and drove 3 car lengths from my drive way, my dash screen notified me with “Check ABS, Check Brake System, and Check VSC System” all with “Have your car checked by a dealer”. I reversed the car and returned to my driveway. My husband called a friend mechanic shop owner who ran the diagnostic report that showed a C1391code. I remembered I received a notification letter regarding this issue and called the dealer. Service agent indicated that without Toyota doing the diagnostic run on my vehicle, they could not give me any quote on the price, but notified me that the letter I received had expired on December 31, 2020 or 10 years or 150,000 miles. My Highlander had this alert screen notification at 144,000 miles. I was told I would be responsible for repair charges. Feeling very frustrated, I called the Toyota corporate number and spoke to a female who then connected me with a supervisor. I explained my experience and the representative explained the notification letter had expired and was unlike a recall, which was indefinite. I emphasized to him that since Toyota knew this was a problem, how could they put an expiration date on the failed Brake Booster Actuator Pump Assembly that they clearly knew was a brake problem. Furthermore, Toyota, which I have been a loyal owner of five vehicles, had only allowed one year + for their accountability to the fixing the brake assembly parts. This meant it was a luck of the draw depending on miles driven for the brake assembly to fail during the little more than a year notification period for Toyota to be responsible for replacing the parts. I find this to be very unfair and unjust. I voiced my opinion to the 800 number a second time, & was told that if the NHTSA had determined it a recall, no expiration date. As a senior citizen who is on a fixed income, I believe Toyota should fix all Brake Booster Actuator Pumps that fail and NHTSA should demand a recall.
Service brakes, Feb 15, 2022
The Brake Actuator Assembly and Brake Booster Pump Assembly have failed on my 2008 Toyota Highlander Hybrid. As I understand, this is a common problem for my vehicle and Toyota has agreed to fix it if the mileage is under 150,000 miles (which mine is) AND the time since first use is less than 10 years (which is not the case.) For this safety issue, I think Toyota should be standing behind the safety of their vehicles and fix my brake pump. This is putting my family at risk. This issue has been confirmed by my local independent auto service company. The warning lights came on after the failure (brake, ABS, master warning, traction control).
Service brakes, Dec 16, 2021
The ABS ACTUATOR failed in my 2008 Toyota Highlander Hybrid. The screen inside the car flashed ABS // VSC // CHECK BRAKE SYSTEM. Vehicle is at 144,000 miles The component is out of stock nationwide and Toyota dealer has issued a warranty extension.
Service brakes, Dec 3, 2021
On November 26, 2021 my 2008 Highlander Hybrid started displaying Check ABS, Check VSC System, Check Brake System and Brake Malfunction, errors on the display screen. I could feel the the grinding noise and brake pedal seemed different than normal. The Brake Malfunction error was displayed with a warning to "Stop the vehicle in a safe place immediately, and contact a dealer". I bought a vehicle diagnosis code reader and it showed C1391 (Abnormal Leak in Accumulator Pressure). I received the same code late last year in 2020 and took my vehicle to dealer. They told me that I was not driving my vehicle due to pandemic and the 12V battery went bad. They removed the errors and I replaced the battery from Walmart. I did not see the error code again until now (after 1 year). I received a Customer Support Program Bulletin letter (POL19-06) from Toyota in 2019 or early 2020 which mentioned C1391 as a verification of problem in vehicle. I showed it to the dealership during my 2020 visit and they said my vehicle is not covered. I believed them since I did not see the error again after replacing the 12V battery. Now I am having the same problem again. The ABS error was displayed on 11/26/2021. I was able to read and reset the ABS error code C1391 on 11/30/2021. The ABS error showed up again on 12/2/2021 while I was driving the car with my family in it. I had to reset it to reach home safely. It ABS error came back ON again before reaching home. I am unable to get it fixed because the extended warranty provided by Toyota for this known safety issue expired on 12/31/2020 and now I am billed for the replacement parts and labor ($4000). Toyota should have opened a recall for this faulty ABS system or should not have an expiry date to this program. After searching the internet I am also surprised that this problem is not only with Highlander Hybrid but though out Toyota and Lexus product lines. I request you to please ask Toyota to open a recall on this life threatening issue.
Engine, Fuel/propulsion system, Nov 12, 2021
On January 19, 2021, after driving for about two hours, I suddenly started to hear an unusual knocking noise from the engine. I slowed down, but I was unable to pull over immediately because I was driving on a very dark two lane highway, with no safe shoulder. After the same noise continued for about five to ten minutes, a light began to flash indicating extremely low oil pressure, and warning that the car should stop immediately. At that point, fortunately, I was able to pull over at a gas station, where I discovered that oil was gushing from my engine onto the ground. I checked my oil dipstick and noted that the car had no oil, and was thus inoperable. I was extremely concerned that the engine had been damaged while being driven with little to no oil. In 2014, Toyota issued a notice of a Warranty Enhancement Program – ZE2, related to extending warranty coverage for repairs related to a leaking or seeping engine oil cooler pipe. I never received any owner notification of this issue in 2014. Toyota refused to pay for the repair in 2021, and now in November 2021, the engine has quit due to the damage incurred in January 2021. The engine oil cooler pipe is defective and my family could have been seriously injured or killed by its catastrophic failure.
Engine, Sep 29, 2021
On September 25, 2021, my husband was driving our 2008 Highlander locally to the store. The low pressure light came on and said pull over immediately. He pulled over and and checked the oil dip stick and our car was totally out of oil. He also notice oil under our car and a line of oil going up the street. The following day, I contacted Toyota Experience Center and was informed their were no service campaigns on my Highlander. I had the car towed to my local mechanic and he verified that the car had no oil and replaced the failed oil cooler hose. My concern is that the oil cooler hose failed, draining all of the oil in minutes. I feel this is a safety issue because of how rapidly it occurred and If we couldn't immediately stop the car our engine could have seized up and made the car stop.
Service brakes, Aug 27, 2021
On approx. August 13, 2021, my 2008 Toyota Highlander Hybrid vehicle began making grinding sounds when the brake is fully depressed while the transmission lever is set to "drive". On approx. August 20, 2021, my vehicle started showing 4 error messages on the display: Brake Malfunction, Check ABS, Check VSC System, and Check Brake System. The Brake Malfunction error was displayed with a warning to "Stop the vehicle in a safe place immediately, and contact a dealer". At the same time, these 5 warning lamps became illuminated: Brake System Warning Light and Warning Buzzer (Red), Brake System Warning Light (Yellow), Master Warning Light (Yellow), ABS Warning Light (Yellow), and SLIP Indicator (Yellow). A car repair technician obtained the following error codes from the vehicle in a diagnosis: C1241 (Low or High Power Supply Voltage), C1253 (Pump Motor Relay), and C1391 (Abnormal Leak in Accumulator). I was informed that the VSC (vehicle stability control) safety feature of the vehicle is disabled while the error codes and messages are present. Toyota previously issued a customer support bulletin (No. POL19-06) on June 6, 2019, titled "Customer Support Program ZKC: Certain 2008-2010 Model Year Highlander Hybrid Vehicles Coverage for Brake Actuator Assembly and Brake Booster Pump Assembly". In the bulletin, Toyota acknowledged that its 2008-2010 Highlander Hybrid models had "certain internal malfunctions of the Brake Actuator Assembly". Affected error codes include C1391, C1252, C1256, and C1253. Affected warning lamps consists of all 5 of the warning lamps that were illuminated in my vehicle. Affected parts include 04008-26448 (Actuator Assy, Brake w/ Fluid) and 04008-51148 (Pump Kit, Brake Booster w/ Accumulator). Instead of issuing a recall for this hazardous defect, Toyota opted to offer "Customer Support Program ZKC". The malfunction that manifested my vehicle is not eligible for this program. Toyota should issue a proper recall to address this safety hazard.
Service brakes, Aug 20, 2021
2008-2010 Toyota Highlander (hybrid, in my case) has an ongoing problem with the brake actuator and brake booster. In my case, within a year I will have had these items replaced twice. The cost to me will be about $3000. According to many website chats and blogs, this is a repeated repair even after having replaced it.
Air bags, Jul 12, 2021
srs light stays on. have seen many comp;aints on this with 2008 highlander. many say its a wiring problem in steering column.