2003 Ford Escape
Problems, recalls and owner-reported issues
Structure is the leading concern among 598 owner complaints filed for this model year. This is the 17th highest complaint count among 26 Escape model years with reports.
Of the 2003 reports, 44 involved a crash and 29 involved a fire. 32 people were injured.
What owners report most often
Recalls and investigations
Power train, automatic transmission, lever and linkage, floor shiftSep 29, 2015
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Campaign 15V606000 on NHTSA.gov
Suspension, front, wheel bearingJun 3, 2015
The Timken Company (Timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from January 22, 2015, to May 21, 2015, to be used as service parts on 2001-2012 Ford Escape, 2001-2011 Mazda Tribute, and 2005-2011 Mercury Mariner vehicles. The affected wheel bearings have incorrect dimensions of a 42mm bore, 76mm outer dimension, and 39mm width, instead of a 42mm bore, 78mm outer dimension and a 45mm width.
Use of an incorrectly sized wheel bearing can adversely affect the braking and steering of the vehicle, increasing the risk of a crash.
Timken has begun notifying distributors who will offer purchasers replacement wheel bearings, free of charge. The recall began on May 21, 2015. Owners may contact Timken customer service at 1-866-984-6536.
Campaign 15E045000 on NHTSA.gov
Structure, frame and membersApr 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2001-2004 Escape vehicles manufactured October 22, 1999, through January 23, 2004, originally sold, or currently registered in, Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia. These vehicles may experience excessive corrosion at the forward attachment of the lower control arm.
A separation of the lower control arm can result in a significant loss of steering control, increasing the risk of a crash.
Ford will notify owners, and dealers will install a newly designed reinforcement cross-brace, free of charge. The recall began on May 30, 2014. Owners may contact Ford at 1-800-392-3673. Ford's number for this recall is 14S02.
Campaign 14V165000 on NHTSA.gov
Engine and engine coolingJul 26, 2012
Ford Motor Company is recalling certain model year 2001 through 2004 Escape vehicles equipped with 3.0L V6 engines and speed control manufactured from October 22, 1999, through January 23, 2004. Inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. This risk exists regardless of whether or not speed control (cruise control) is used.
A stuck throttle may result in very high vehicle speeds and make it difficult to stop or slow the vehicle, which could cause a crash, serious injury or death.
Ford will notify owners, and dealers will repair the vehicles by increasing the engine cover clearance, free of charge. The safety recall began August 3, 2012. Remedy parts are expected to be available in mid-August 2012. Until then dealers will disconnect the speed control cable as an interim remedy, if parts are not available at the time of an owner's service appointment. Owners may contact Ford at 1-866-436-7332.
Campaign 12V353000 on NHTSA.gov
Service brakes, hydraulic, antilock/traction control/electronic limited slip, control unit/moduleApr 10, 2007
ON CERTAIN SPORT UTILITY VEHICLES EQUIPPED WITH ANTILOCK BRAKES (ABS), THE ABS MODULE CONNECTOR MAY HAVE MISSING OR DISLODGED WIRE SEALS. THIS CONDITION COULD ALLOW CONTAMINATION TO ENTER THE MODULE CONNECTOR, CREATING A POTENTIAL FOR AN ELECTRICAL SHORT.
AN ELECTRICAL SHORT MIGHT CAUSE AN ABS MALFUNCTION THAT WOULD ILLUMINATE THE ABS WARNING LIGHT, AND IN SOME CASES, THE MODULE MAY OVERHEAT RESULTING IN BURNING ODOR, SMOKE, AND/OR FIRE. THIS CONDITION COULD OCCUR EITHER WHEN THE VEHICLE IGNITION SWITCH IS IN THE OFF POSITION OR WHILE THE VEHICLE IS BEING OPERATED.
DEALERS WILL INSPECT THE WIRE HARNESS CONNECTOR TO THE ABS MODULE FOR MISSING OR DISLODGED WIRE SEALS, AND REPAIR OR REPLACE THE HARNESS CONNECTOR AS APPROPRIATE. THE DEALER WILL ALSO INSPECT THE CONNECTOR ON THE ABS MODULE AND REPLACE IT IF IT IS FOUND TO BE CORRODED OR DAMAGED. THE RECALL BEGAN ON APRIL 23, 2007. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
Campaign 07V156000 on NHTSA.gov
Service brakes, hydraulic, foundation components, master cylinderMar 29, 2007
CERTAIN CARDONE MASTER CYLINDERS WITH PART NUMBERS 10-2925, 10-2987, 10-2987MZA, 10-3083, 11-3015, 11-3042, 11-3044, 11-3045, 11-3047, 11-3064, AND 11-3156, AND WITH DATE CODES LOWER THAN DCA7078 SOLD AS REPLACEMENT EQUIPMENT FOR USE ON THE VEHICLES LISTED ABOVE. THE SEAL ON MASTER CYLINDER CAN FAIL AND LEAK BRAKE FLUID.
LOSS OF BRAKE FLUID CAN RESULT IN POOR BRAKING PERFORMANCE, POSSIBLY RESULTING IN A VEHICLE CRASH.
CARDONE WILL NOTIFY OWNERS AND OFFER TO REPURCHASE ANY DEFECTIVE MASTER CYLINDERS. THE RECALL BEGAN DURING APRIL 2007. OWNERS CAN CONTACT CARDONE AT 1-800-777-4780.
Campaign 07E023000 on NHTSA.gov
Latches/locks/linkages, doors, latchDec 20, 2004
CERTAIN 2004-2005 SPORT UTILITY VEHICLES AND CERTAIN 2001-2003 SPORT UTIITY VEHICLE HAVING REAR LIFTGATE COMPONENTS SERVICED WITH 2004 EQUIVALENT COMPONENTS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 206, 'DOOR LOCKS AND DOOR RETENTION COMPONENTS.' THE REAR LIFTGATE LATCHING SYSTEM DOES NOT MEET THE INERTIA LOAD REQUIREMENT IN ONE DIRECTION.
IF THE LIFTGATE IS LEFT UNLOCKED, THERE IS THE POTENTIAL THAT IT MAY OPEN DURING A CRASH.
DEALERS WILL REPLACE THE REAR LIFTGATE LATCH RELEASE ROD, THE RELEASE ROD ATTACHMENT CLIP AND THE DOOR HANDLE RETURN SPRING. THE RECALL BEGAN ON MARCH 31, 2005. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.
Campaign 04V602000 on NHTSA.gov
Vehicle speed control, cablesDec 7, 2004
ON CERTAIN SPORT UTILITY VEHICLES BUILT WITH 3.0L V6 ENGINES, THE ACCELERATOR CABLE MAY PREVENT THE THROTTLE FROM RETURNING TO THE IDLE POSITION.
AN UNEXPECTED INCREASE IN ENGINE IDLE SPEED MAY INCREASE STOPPING DISTANCE AND MAY RESULT IN A VEHICLE CRASH.
DEALERS WILL REPLACE THE ACCELERATOR CABLE. THE RECALL BEGAN ON JANUARY 10, 2005. OWNERS SHOULD CONTACT FORD AT 1-866-436-7332.
Campaign 04V574000 on NHTSA.gov
Power train, automatic transmission, control module (tcm/pcm/tecm)Apr 6, 2004
ON CERTAIN SPORT UTILITY VEHICLES EQUIPPED WITH 3.0L V6 ENGINES, DURING DECELERATION, THE ENGINE CAN STALL.
SHOULD THE ENGINE STALL, A VEHICLE CRASH COULD OCCUR.
DEALERS WILL REPROGRAM THE POWER CONTROL MODULE (PCM) WITH THE APPROPRIATE CALIBRATION. OWNER NOTIFICATION BEGAN ON APRIL 21, 2004. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.
Campaign 04V165000 on NHTSA.gov
Representative owner complaints: service brakes
61 reports, newest first. Show all
Service brakes, Hydraulic, Feb 11, 2005
THE CONSUMER IS EXPERIENCING PROBLEMS WITH THE BRAKES. THE BRAKES WERE COMPLETELY HARDENED. THE VEHICLE HAS BEEN DRIVEN OVER MOUNTAINOUS TERRAIN AND THE BRAKES BURN OUT VERY QUICKLY DRIVING UNDER THESE MOUNTAINOUS CONDITIONS. OWNER HAS CONTACTED THE DEALER AND HAS HAD THE PADS AND ROTORS REPLACED. PROVIDE FURTHER DETAILS.*JB
Service brakes, Air, Dec 15, 2004
WHILE ON A RETURN LONG DISTANCE ROAD TRIP MY ABS DASH LIGHT CAME ON AND REMAINED ON. AFTER STOPPING AND RESTARTING THE VEHICLE THE LIGHT DID NOT RETURN UNTIL FARTHER DOWN THE ROAD. I CONTACTED THE DEALERSHIP THE FOLLOWING DAY MADE AN APPOINTMENT AND THEY DETERMINED THAT A SPEED SENSOR HAD GONE BAD.*AK
Service brakes, Hydraulic, Nov 23, 2004
FORD ESCAPE XLT 2003 RAKE PADS WORN TO LESS THAN 4 MPH AND ROTORS WORN TO .910 AT 15,153 MILES. I CONSIDER THIS EXCESSIVE WEAR.*AK
Service brakes, Hydraulic, Sep 21, 2004
COMPLETE FAILURE OF BRAKES - PADS AND ROTORS - WITH ONLY 19,000 MILES ON VEHICLE. REPLACED AT MY COST - ZERO ACCEPTANCE OF RESPONSIBILITY FROM FORD. SERVICE ADVISOR SAID IT IS A COMMON PROBLEM WITH ORIGINAL FORD BRAKES - REPLACEMENTS GENERALLY LAST LONGER.*AK
Service brakes, Hydraulic, Tires, Oct 1, 2003
WHILE DRIVING THE LEFT REAR TIRE TREAD SEPARATED AND THE TIRE BLEW OUT. THE DRIVER WAS ABLE TO DRIVE THE VEHICLE OFF THE ROAD. THE TIRE WAS ORIGINAL EQUIPMENT (TIRE SIZE P235.70R16) . DEALER NOTIFIED AND INFORMED CONSUMER THAT THE CAUSE WAS UNDETERMINED. THE VEHICLE BRAKES AND ROTORS FAILED WHICH CAUSED NOISE WHILE BRAKING. *AK *NLM
Steering, Service brakes, Hydraulic, Sep 12, 2003
THERE WAS A GROANING NOISE COMING FROM THE BRAKES, WHEN THE VEHICLE WAS AT A COMPLETE STOP BUT IDLING. THERE WAS ALSO A BURNING SMELL COMING FROM THE AIR VENTS. UPON INSPECTION OF THE VEHICLE BY THE DEALERSHIP THE STEERING PUMP AND PRESSURE LINE HAD RUPTURED. THE DEALERSHIP INDICATED IT WAS CAUSED BY THE POWER STEERING FLUID BEING CONTAMINATED. *AK *SCC *JB
Steering, Service brakes, Hydraulic, Engine and engine cooling, Aug 1, 2003
WHILE DRIVING AT 50/55 MPH VEHICLE DIED OUT WITHOUT WARNING. THIS RESULTED IN LOSS OF POWER STEERING AND BRAKES.THE COST FOR REPAIRS WERE $114.21. *AK *CB
Service brakes, Hydraulic, Jul 28, 2003
3 WEEKS AFTER BUYING VEHICLE IT STARTED MAKING NOISE WHEN APPLYING BRAKES. DEALER STATED THAT WAS NORMAL FOR A NEW CAR. *AK
Service brakes, Hydraulic, Jul 23, 2003
I HAVE A 2003 FORD ESCAPE. ON APRIL 17, 2003 I TOOK MY VEHICLE INTO THE FORD DEALERSHIP IN VACAVILLE WITH A COMPLAINT ABOUT THE BRAKES MAKING A GRINDING NOISE (25,503 MILES). THEY TOLD ME THAT THEY COULD NOT DUPLICATE THE NOISE AND CHECKED THE FRONT BRAKES. THEY CLAIMED TO HAVE MEASURED THE BRAKE PADS AT ABOVE 5MM OF PAD REMAINING. THE NOISE CONTINUED. I TOOK THE VEHICLE BACK TO THE DEALERSHIP ON JUNE 27, 2003 (28,720 MILES). THIS TIME THEY HEARD THE NOISE AS WELL AS A BEARING NOISE. THEY MEASURED THE BRAKES AT 3MM AND TOLD ME THAT THE ROTORS MAY BE WARPED. I LEFT THE VEHICLE FOR THE BEARING REPAIR AND RECEIVED A PHONE MESSAGE (ON MY ANSWERING MACHINE) THAT THEY RE-MEASURED THAT BRAKE PADS AND FOUND THEM TO BE 2MM NOT 3MM. THEY DIDN'T MENTION ANYTHING ABOUT THE ROTORS. I ASKED ABOUT THE EXCESSIVE WEAR OF THE BRAKE PADS AND THEY SAID THAT IT WAS NORMAL WEAR. THEY TOLD ME THAT THEY COULD DO NOTHING ABOUT THE PADS OR THE ROTORS. I CALLED MY BROTHER-IN-LAW THAT WORKS FOR FORD AND TOLD HIM ABOUT MY EXPERIENCE. HE MADE SOME PHONE CALLS AND FOUND OUT FROM ONE OF FORD'S ENGINEERS THAT THEY HAVE PROBLEMS WITH BRAKE WEAR (BOTH PADS AND ROTORS) ON THE ESCAPE AND THE FORD FOCUS. TODAY (30,270 MILES) I TOOK MY ESCAPE TO MIDAS AND HAD A BRAKE INSPECTION. THE MIDAS EMPLOYEE SAID THAT THE ROTORS ARE WORN DOWN BELOW SPECS AND NEED TO BE REPLACED. HE ALSO SAID THAT THE ROTORS SHOULD NOT WEAR THAT QUICKLY. AS TO THE PADS HE SAID THAT IT WAS NORMAL WEAR BECAUSE THEY ARE CERAMIC PADS. I WENT TO THE FORD DEALERSHIP IN VACAVILLE WITH THIS INFORMATION. THEY TOLD ME THAT THERE WAS NOTHING THAT FORD COULD DO FOR ME ABOUT THE BRAKE ROTORS. THE INDIVIDUAL TOLD ME THAT FORD USES SOFT ALUMINUM ROTORS ON BOTH THE ESCAPE AND THE FOCUS AND THEY WEAR OUT VERY QUICKLY. MY CONCERN FOR FORD IS THAT IF THEY USE SUBSTANDARD EQUIPMENT AND DO NOT SEEM TO BE CONCERNED, ARE THEY NOT OPENING THEMSELVES UP TO A LAW SUIT IF THEIR "SOFT ROTORS" FAIL AND CAUSE AN ACCIDENT. *AK
Service brakes, Hydraulic, Power train, Apr 28, 2003
WHEN THE CAR IS PUT INTO REVERSE IT DOES NOT WANT TO MOVE. IF YOU INCREASE THE RPM'S, IT STILL JUST SETS THERE. THE PROBLEM HAS BEEN VERY INCONSISTENT. REVERSE SEEMS TO BE AT THIS POINT, THE ONLY PLACE IT OCCURS. IN ONE OF THE ATTEMPTS TO FIX THE PROBLEM, THE TECHNICIAN FOUND THAT 3 OF THE 4 CALIPERS WERE FROZE/DRIED UP. THIS DOES NOT SET WELL WITH ME AND I SEE IT AS A POSSIBLY DANGEROUS SITUATION. *NLM
Service brakes, Hydraulic, Feb 10, 2003
THE BRAKE AND ACCELERATOR PEDAL WAS DESIGNED TO CLOSE TOGETHER, WHICH CAUSED CONSUMER TO PRESS THE ACCELERATOR WHEN THE BRAKE WAS BEING APPLIED.*JB *JB