2013 Ford Focus
Problems, recalls and owner-reported issues
Power train is the leading concern among 2,112 owner complaints filed for this model year. This is the 4th highest complaint count among 19 Focus model years with reports.
Of the 2013 reports, 49 involved a crash and 12 involved a fire. 28 people were injured and 3 people died.
What owners report most often
Recalls and investigations
Fuel system, gasoline, storage, evaporative emissions, canisterJun 9, 2026
Ford Motor Company (Ford) is recalling certain 2012-2018 Focus vehicles previously repaired incorrectly under recall number 18V735. The Canister Purge Valve (CPV) may malfunction, causing the engine to stall unexpectedly while driving.
An engine that stalls while driving increases the risk of a crash.
Dealers will update the powertrain control module (PCM) software, free of charge. Owner notification letters were mailed July 29, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S40. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
Campaign 26V369000 on NHTSA.gov
Equipment, electrical, engine block heaterJan 15, 2026
Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
An electrical short circuit can increase the risk of a fire.
Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed March 6, 2026. Additional letters will be sent once the final remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S01. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026.
Campaign 26V011000 on NHTSA.gov
Latches/locks/linkages, doors, latchJun 8, 2020
Ford Motor Company (Ford) is recalling certain 2011-2014 Fiesta, 2013-2014 Fusion, 2015 Mustang, 2013-2015 Escape and C-Max, 2012-2015 Focus, 2014-2016 Transit Connect, 2013-2014 Lincoln MKZ, and 2015 MKC vehicles. These vehicles were previously recalled and repaired under recalls 15V-246, 16V-643 or 17V-210, however the repair may not have been completed properly. A component within the door latches may break making the doors difficult to latch and/or leading the driver or a passenger to believe a door is securely closed when, in fact, it is not.
A door that is not securely latched could open while the vehicle is in motion, increasing the risk of injury to a vehicle occupant.
Ford will notify owners, and dealers will inspect the latch date codes to confirm if the repair was done correctly, and replace the side door latches if necessary, free of charge. Owners will also have the option to inspect their own vehicle's door latches and enter the date codes into a website to determine if the latches are correct. Owner notification letters were mailed on July 27, 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S30.
Campaign 20V331000 on NHTSA.gov
Fuel system, gasoline, storageJul 5, 2019
Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
Campaign 19V515000 on NHTSA.gov
Fuel system, gasoline, storageOct 22, 2018
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Campaign 18V735000 on NHTSA.gov
Latches/locks/linkages, hatchback/liftgate, lockSep 28, 2016
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Campaign 16V698000 on NHTSA.gov
Latches/locks/linkages, doors, latchSep 6, 2016
Ford Motor Company (Ford) is recalling certain model year 2012-2015 Ford Focus, 2013-2015 Ford Escape and Ford C-MAX, 2015 Lincoln MKC and Ford Mustang, and 2014-2016 Ford Transit Connect vehicles. A component within the door latches may break, preventing the doors from latching and/or leading the driver or a passenger to believe a door is securely closed when, in fact, it is not.
A door that is not securely latched could open while the vehicle is in motion, increasing the risk of injury to a vehicle occupant.
Ford will notify owners, and dealers will replace the door latches with an improved part, free of charge. The recall began on January 27, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S30.
Campaign 16V643000 on NHTSA.gov
Electrical system, wiringDec 2, 2015
Ford Motor Company (Ford) is recalling certain model year 2013 Escape vehicles manufactured January 11, 2012, to April 1, 2013, and 2013-2014 Focus ST vehicles manufactured May 03, 2012, to October 14, 2013. Insufficient compression in the engine wiring harness splices to the Manifold Absolute Pressure (MAP) sensor may provide incorrect signals to the powertrain control module (PCM).
The incorrect signals could cause the vehicle to hesitate or the engine to stall, increasing the risk of a crash.
Ford will notify owners, and dealers will replace the current crimped splices with new splices, free of charge. The recall began on January 7, 2016. Owners may contact Ford customer service 1-866-436-7332. Ford's number for this recall is 14S17-S1.
Campaign 15V813000 on NHTSA.gov
Electrical system, wiringAug 11, 2014
Ford Motor Company (Ford) is recalling certain model year 2013-2014 Escape vehicles manufactured October 5, 2011, to April 1, 2013, and equipped with 2.0 liter engines and Focus ST vehicles manufactured February 14, 2012, to October 14, 2013, and equipped with 2.0 liter engines. Insufficient compression in the engine wiring harness splices to the Manifold Absolute Pressure (MAP) sensor may provide incorrect signals to the powertrain control module (PCM).
The incorrect signals could cause the vehicle to hesitate or the engine to stall, increasing the risk of a crash.
Ford will notify owners, and dealers will replace the current crimped splices with new splices, free of charge. The recall began in October 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S17.
Campaign 14V495000 on NHTSA.gov
Exterior lightingAug 1, 2013
Ford is recalling certain model year 2012-2013 Focus BEV vehicles equipped with High Intensity Discharge (HID) headlights, manufactured September 15, 2011, through May 6, 2013; and model year 2013 Focus ST vehicles equipped with High Intensity Discharge (HID) headlights, manufactured February 16, 2012, through May 7, 2013. Due to a wiring incompatability, the front side marker lamps may not function. Thus, these vehicles fail to comply to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, Reflective Devices, and Associated Equipment."
Without the proper illumination of the side maker lamps, the vehicle may be less visible in night time conditions, increasing the risk of a crash.
Ford will notify owners, and dealers will modify the headlamp assembly wiring, free of charge. The recall began on August 16, 2013. Owners may contact the Ford customer relationship center at 1-866-436-7332. Ford's recall number is 13C04.
Campaign 13V335000 on NHTSA.gov
Latches/locks/linkagesMar 7, 2013
Ford is recalling certain model year 2013 Focus and C-Max vehicles built from November 16, 2012, through November 21, 2012; and model year 2013 Escape vehicles manufactured from November 14, 2012, through November 21, 2012. The left rear door child lock was built incorrectly. As a result, the child lock may not engage when the operator uses normal force to activate the child lock.
The operator may incorrectly believe the child lock is engaged. However, the door may be opened from the inside, increasing the risk of injury to an unrestrained child.
Ford will notify owners, and dealers will inspect the affected rear door latches, and replace them as necessary, free of charge. The recall began on March 27, 2013. Owners may contact Ford Motor Company Customer Relationship Center at 1-866-436-7332.
Campaign 13V085000 on NHTSA.gov
EquipmentOct 2, 2012
This recall involves aftermarket parts sold by Yakima Products, Inc. for use on model year 2012 and 2013 Ford Focus vehicles. This recall is being conducted by Yakima, not by Ford. Certain combined Q-Tower and Q128 Clip rooftop rack systems, part numbers 8000124 and 8000728, do not fully contact the door frame.
Without proper contact of the rooftop rack clip to the door frame, there is insufficient clamping pressure and friction. The system may slide off the vehicle when loaded with accessories, possibly becoming a road hazard to other vehicles or causing injury to pedestrians.
Yakima will notify owners, and Yakima or a Yakima dealer will refund the purchase of the Q-Tower and Q-128 Clip system. There is no replacement system available for the 2012-2013 model year Ford Focus. The safety recall began on October 15, 2012. Only vehicles equipped with the vehicle rack system are affected. This recall is being conducted by Yakima, not Ford. Owners may contact Yakima at 1-888-925-4621.
Campaign 12E035000 on NHTSA.gov
Representative owner complaints: fuel/propulsion system
209 reports, newest first. Show all
Electrical system, Engine, Fuel/propulsion system, Sep 23, 2026
The vehicle suffered a major mechanical and electrical failure on July 28, 2026, and was immediately towed to an authorized dealership. After a multi-day delay awaiting a senior technician's analysis, the dealership issued a single service ticket grouping two distinct issues: a failed Canister Purge Valve (active Safety Recall 26S40) and localized wiring damage. The dealership fraudulently drafted the ticket to imply that external rodent damage caused the recall component failure. However, forensic photographic proof uploaded to the manufacturer database on August 13, 2026, reveals a classic consequential engineering failure: the wiring insulation is severely bubbled and thermally fused from extreme internal circuit resistance caused entirely by the defective recall component. An adjacent plastic snack wrapper remains completely pristine and untouched, disproving the rodent narrative. The vehicle has now been held in safety detention for 57 consecutive days. A corporate supervisor explicitly confirmed on a recorded line that the manufacturer has possessed these forensic photos since mid-August but left the safety file stagnant due to an internal database text-field error. Their software is failing to match the vehicle's engine string '2.0L I4 DI Ti-VCT' to the recall applicability screen 'GDI', creating a data-entry roadblock to deny a free safety remedy. I am requesting an immediate federal audit of the manufacturer's database alignment for Recall 26S40 and a manual technical override directive to initiate repairs. Manufacturer Master Case: CHX-09386351-T9Y5H1.
Electrical system, Engine, Fuel/propulsion system, Jul 14, 2026
The evap canister purge valve has been a recurring problem for this vehicle. The canister was replaced in 2021, but continued having problems, as it pulled a vacuum on the fuel tank in upwards of 3/8 inch. (Documented by Murray Ford in 2023 and reassuredthere was no issue by them) the vehicle has displayed inaccurate fuel readings and caused our family to be disabled and then stranded in the night on highway 95. It put the safety of my family, and other motorists at risk The problem hasn't been duplicated because their "software fix" essentially ignored the problem altogether. There were no warnings. According to my vehicle it had at least 50 miles til empty. The fuel sending unit is displaying innacurqte fuel readings, and the fuel pump has displayed symptoms, characterized by surging, stalled when accelerating from a stop, and of course, completely shutting off, while on the highway. I've tried my best to trust and be patient with Ford and for them to do the right thing, but have been brushed off.
Engine, Fuel/propulsion system, Jul 14, 2026
I am reporting a severe vehicle safety hazard and engine stalling incident on my 2013 Ford Focus caused by an un-remedied factory emissions safety defect (related to Ford Recall 26S40 / 18S32). Due to an incomplete factory software monitoring patch, the canister purge valve stuck open and allowed continuous, unchecked engine vacuum to pull straight out of the plastic fuel tank. This heavy vacuum physically collapsed and deformed the bottom of the plastic fuel tank inward by approximately 0.25 to 0.375 inches. This structural collapse compressed the internal fuel pump assembly and mechanical float arm, falsifying the dashboard fuel gauge and distance-to-empty calculations. On April 2nd, while driving on Interstate 95 at midnight, the vehicle displayed an inaccurate fuel level, ran completely dry, and suffered a sudden engine stall in high-speed traffic without warning. My family and I were trapped in a highly hazardous situation and were forced to physically push the disabled vehicle 3 miles down the highway in total darkness. We ultimately had to enlist the emergency intervention of the Florida State Patrol Road Rangers to dispatch a unit and supply fuel so we could safely clear the interstate. The vehicle has since thrown a hard diagnostic trouble code P0443, confirming a complete electrical circuit malfunction of the EVAP system. Ford's failure to successfully deploy a functional software monitor has caused severe structural damage to my fuel system and created an imminent, life-threatening safety risk to my family on public highways. I am requesting a federal record of this incident to compel a full vehicle inspection and complete fuel system component replacement by the manufacturer."
Fuel/propulsion system, Jun 4, 2026
I had my purge valve replaced under 24N07 ford costumer satisfactory program and the faulty purge valve damaged my catalytic converter and caused my engine light to illuminate with P0420.
Other or unspecified, Engine, Fuel/propulsion system, Apr 14, 2026
The vehicle began to experience issues where it was difficult to start and ran rough. Multiple times after turning off vehicle and attempting to restart later it would not restart. Had vehicle towed to dealership for repairs, they conducted a recall repair and test over multiple days. Picked up vehicle, drove approximately 7 miles. Went into store came back and vehicle would not start. Multiple other recalls are listed for this date range and motor that likely could be impacting my current vehicle. However, this VIN is not listed as a specific recall. Current situation places driver and passenger at risk as the vehicle does not run properly and does not restart
Electrical system, Fuel/propulsion system, Dec 4, 2024
There is an issue with the vehicle not receiving gasoline and the car has left me stranded
Power train, Fuel/propulsion system, Jun 7, 2024
I have had multiple instance of losing power with my car, I completed Customer Satisfaction Program 14M02 and the known issue was not solved. I then went to a mechanic to have a diagnostic test performed due to the check engine light being on and they concluded that the issue was the Canister Purge Valve as well as possibly the Charcoal Canister due to the CPV malfunctioning. Other than losing power within my car the other associated problems, as confirmed by mechanic, are rough idling, difficulty starting, decreased fuel economy, and increased emissions.
Fuel/propulsion system, Nov 7, 2023
The canister purge valve has failed. Was not defective when recall #19S22 was performed. Car failed to start repeatedly and would not idle after refilling the tank from low (fuel light on) to approximately 75%. Eventually, the car did start and after keeping the RPMs at 2000 for a few minutes, the car is back to idling normally. Check engine light did not appear until 3 days after the stall at the gas station, which had a DTC P1450 code indicating inability for the car to bleed the fuel tank, suggesting the canister purge valve. Ford should offer the free replacement of the defective purge valve and inspection of the carbon canister and fuel tank even after the 19S22 recall was performed (which was just a software update and inspection at the time of service). The possibility of the car stalling not just at the gas station is a safety issue for others and the occupant because of the possibility of a sudden loss of power/becoming an obstruction/or abruptly stopping on the road.
Fuel/propulsion system, May 17, 2023
On 4/20/23 while driving home from work on the highway my car stalled and after pulling over would not start. The check engine ight had come one. On 4/21/23 I took my car to a mechanic who found the p0456 fault in the PCM which was tied to an active recall on my vehicle. The mechanic printed out the recall information and recommended replacing the cannister purge valve, fuel tank and fuel pump assembly. They suggested I take it to the local ford dealer to have the recall work done as it would be covered. On 4/27/23 I took my car to the dealership to have the recall work done. The dealer reprogrammed the PCM and replaced the vapor canister purge solenoid. On 5/15/23 while driving home from work on the highway my car stalled again and after pulling over would not start. The fuel tank has deformed, but less than the 1 inch ford is requiring to replace it and the distance to empty is still inaccurate. On 5/16 I dropped the car back off at the dealer. They looked at the car the next day and refused to address the outstanding issues.
Fuel/propulsion system, May 8, 2023
There was a past recall for the purge valve canister and the fuel pump and I was never notified from Ford about the recall when it was open. Now they are asking me to pay out of pocket for these repairs the dealership is asking $1400 to repair. Ford shoild honor there recalls even if the recall is closed. Now that I have the problem with the fuel system it is affecting my fuel tank as well. I have been buying Ford cars for over 20 years. The least they can do is offer financial assistance. If this is affecting my fuel tank now my car can catch on fire. I can't drive my vehicle more than two miles before it starts to slow down. At the time of the recall my vehicle had 83,000 miles. it now has 140,000.
Fuel/propulsion system, Sep 18, 2022
Faulty canister purge valve caused vehicle to stall and shut down while driving on public roads. Canister purge valve is also causing check engine code P0420. Catalytic converter is also giving out while operating causing a lot of white smoke from the exhaust and catalytic converter.
Power train, Fuel/propulsion system, Jul 22, 2022
My daughter has a 2013 Ford Focus SE and has had numerous issues with her transmission which of recent has presented some serious safety concerns. She had driven her car to work and when attempting to leave after work was unable to get her car to move . She put the car in drive and reved the engine then in reverse the same , would not move. We had the car towed to Sarchione Ford of Alliance and was diagnosed as the Transmission Actuator A . My understanding of the Actuator is it engaged the transmission into gear. I recently read an article in a Ford Forum relating to the April 2020 Class Action Suit and I quote a blogger stated that this defect can abruptly cause car to jump into gear which could cause a safety issue . Another blogger stated that he had a similar issue while on an expressway traveling fast and ended up on the shoulder until eventually getting the car to move again. My daughter's Ford Focus 2013 has had 2 recalls issued relating to the transmission. Program #14M01 Transmission Clutch Shudder / Transmission input seal Warranty extension which is no longer valid. Program #14M02 Transmission Control Module which has been extended to 150,000 mile or until February of next year. Both of the said recalls we're mandated due to the numerous safety concerns relating to failure or uprupt operation due to design defect and no fought of the vehicle operation. So I pose a very simple question, why has not Actuator A and B of the Ford Focus been issued recalls when failure of said parts presents safety concerns? There should be a warranty extension mandate to repair at no cost to vehicle owner. All of these said parts work together when operational to perform safe driving practices on the contrary the motorists are left at risk regarding highway safety. I have written a letter to CEO Jim Farley to reevaluate his Customer Satisfaction Program and recall procedure. The NHTSA needs to review the said safety concerns. I have filed with Ford Motor PAS-37493284.
Power train, Electrical system, Fuel/propulsion system, Jun 4, 2022
This message is a complaint about my local car dealership and the car manufacturer of my vehicle. I will try to follow the general guidelines as much as possible. First off, I have a 2013 Ford Focus with numerous recalls. I recently dropped the vehicle off at my local car dealership the have those recalls worked on...and ONLY those recalls. The recalls include: - faulty transmission control module (TCM) - canister purge valve (CPV) being stuck open causing the plastic fuel tank to deform, causing incorrect gas tank readings - door latches not being secure - software update of the vehicle's computer...to also correct false computer readings. Symptoms I have with the vehicle are as follows: - difficulty with ignition, as I have to turn the key multiple times to start the vehicle; also happens when putting in gas - constant jerking of the vehicle while driving, especially when starting from a stop - stalling of the vehicle, especially when driving uphill - engine light always on - incorrect gas reading; fuel gauge goes up and down. When I dropped my vehicle off at the dealership, I was assured that if the problems were any of the recalls, they would be free of charge. Fast-forward a couple of weeks later and I'm being told that I now owe over $1,000 in labor fees! On top of that I am being told that I owe a $180 diagnostic fee. I was told of two things that were replaced on the vehicle: the canister purge valve (which I already stated IS one of the recalls) and some random sensor, which they had no right to replace without my permission. I am being told neither of these things are covered since the car dealership and manufacturer suddenly don't consider these recalls. The excuse I have been given is the "codes" of the vehicle don't give the same information. I am in utter disbelief of everything I am being told. The recall letters clearly state repairs that are part of a recall are free of charge. Absolutely ridiculous.
Power train, Fuel/propulsion system, May 19, 2022
During startup after refilling tank with fresh gas it will putter and hesitate to stay stay on. Engine light came on had codes ran came back as codes P0171 system to lean secondary DTC P1450 unable to bleed up fuel tank. Was told that was caused by the EVAP so I needed that replaced. Then it’s starts again was told it was the canister purge valve. I had my car taken to a ford dealership and was told they didn’t see what the issue was. It is doing all the things that the recalls for the same year make and model did. It needs to be fixed because this is a safety issue. Next step is to hire an attorney and have vehicle throughly looked at.
Power train, Fuel/propulsion system, Apr 11, 2022
I have had my car in at the ford dealership and I have been waiting on parts to come in. The recalls on the car which are the transmission control module and the gas tank deformation recall have not been completed on my vehicle but is showing up in the system as repaired. I have been waiting for over 10 months for these parts to come in for the repairs to be done. Now my car isn’t drivable and just sits in my driveway.
Power train, Fuel/propulsion system, Dec 13, 2021
Check engine light came on Saturday morning on my way to work, When checked it comes up as fault codes P0420, with secondary codes of P144A - EVAP Emission System Purge Vapor Line Restricted/blocked, P1450 - Unable to bleed up fuel tank vacuum, and P0131 - O2 Circuit Low Voltage (Bank 1, Sensor 1), And started stalling after putting new gas in only, and now hesitates at lower gears and has a rougher then normal idle with the rps not staying steady, Also when doing a VIN check on Fords website, or the NHTSA lookup it does not show up as a recall, however when I do a full VIN check it does show under the recalls page, I'm not sure if they marked it as completed for the VIN of this vehicle or not but its doing literally all the stuff stated in Ford Safety Recall 18S32 18V735000 or 19S22 19V515000, but when trying to chat Ford about it they deny there is one even though the NHTSA OVERVIEW states: All of the affected vehicles previously had Ford Safety Recall 18S32 performed; however, updated powertrain control module (PCM) software was not available at that time. Ford Motor Company wants to ensure the software is updated to the most current release available. In some of the affected vehicles, the PCM software may not adequately detect a stuck-open canister purge valve (CPV) within the fuel vapor system. If the CPV malfunctions and sticks open, it can lead to excessive vacuum in the fuel vapor system, allowing the plastic fuel tank to deform. This can cause the following symptoms: • Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0420, P1450, P0443, P0452, P0456, P0460 and/or P2196 • Inaccurate or erratic fuel gauge indication • Inaccurate distance to empty (DTE) • Engine stall and/or other drivability concerns related to stuck open CPV I have only had the car 2 months as of tomorrow, and am a single dad raising my 6 month old son alone, I cannot have this breakdown completely and risk a accident when it should be covered by recall
Fuel/propulsion system, Nov 27, 2021
Daughter's car has hesitation when driving, took to son who is mechanic. He said it has hesitation, cough idle, loss of power and the gas tank is malformed. He said he looked up the vin and it showed recall 18532-51. I looked on fords website and see that this is recall for their reference number 19S22. My son said this is dangerous because that issue with the fuel tank vacuum could cause the gas tank to crack. I called ford service center to schedule a recall repair but they told me her vin does not show that recall. This car has all the symtoms of the recall, the vin showed up for my son, and the recall is mentioned on fords werbsite. We need to have this repaired. It is a known issue for 2012-2013 ford focuses. Why wouldn't her car be covered??
Fuel/propulsion system, Aug 13, 2021
The car stalled several times while driving. After a mechanics evaluation it was determined that there was a fuel delivery problem. After further evaluation it was confirmed that the problem was a defective purge solenoid. This item was recalled by Ford. However, they did not include this vehicle (by date) in the recall. The recall lists cars made until July 2012 and this vehicle was manufactured in May of 2013. The effect of the defective purge solenoid caused damage to other components of the fuel delivery system. I am now forced to pay for the repairs out-of-pocket. For a problem that is known by (and recalled by) Ford but is excluded from the recall. NOT FAIR
Power train, Fuel/propulsion system, Jul 16, 2021
After driving my vehicle it stalls once it is stopped and I try to press the gas. This can cause a collision. This can either be the fuel system which they did have a recall on my car but the dealership decided it wasn't needed at the time. It could also be the power train. This incident has occurred multiple times since 2017.
Power train, Engine, Fuel/propulsion system, Jul 15, 2021
Check engine light came on. Before I had a chance to get it checked, the engine wouldn't start after refueling until trying on the fourth time. Took the car to a parts store and the code read P1450. An October 25, 2018 recall acknowledged a problem with 2012-18 Ford Focuses with a 2.0L engine. Although this problem is clearly acknowledged with this same year, model, and engine, my VIN is allegedly not covered in the recall. Dealer will not service the car under the recall.
Fuel/propulsion system, May 3, 2021
MY CAR WHEN AT IDLE OR DRIVING AT LOW RPM (900-2000) WILL STALL OUT AND NOT START FOR A WHILE. IVE REPLACED FUEL PRESSURE SENSORS AND THE INJECTION PUMP, AND IT STILL STALLING.
Power train, Electrical system, Fuel/propulsion system, Apr 10, 2021, crash
DOESN'T ACCELERATE HALF THE TIME WHEN I HIT GAS. DOESN'T GO REVERSE HALF THE TIME I PUT IT IN REVERSE. SHUTS OFF RANDOMLY. SHAKES , SHUTTERS. HAD CODES P07A3 AND P2872 SHOW UP AND FORD SAID THEY AREN'T TRANSMISSION RELATED EVEN THO BOTH CODES HAVE THE WORD " TRANSMISSION IN THE CODE SUMMARY. COULDN'T GET INVOLVED IN 55MILL LAWSUIT BECAUSE I HAVEN'T HAD 2 REPAIRS ON IT. BEEN IN SHOP SINCE 50K MILES GETTING SENIORS AND STUFF REPLACED. CAR HAS NEVER IMPROVED EVEN THO I KEEP SPENDING MONEY. IT'S BEEN IN SHOP 3 WEEKS NOW. THEY SAID MIGHT BE TRANS ISSUE NOW BUT THE RADIATOR IS MESSED UP AND THEY CAN'T PROCEED WITHOUT 600 DOLLARS. HELP BEFORE CAR KILLS SOME1. MILLIONS OF YOUTUBE VIDEOS SHOW SAME ISSUES I HAVE. FORD DON'T DO ANYTHING BUT DENY CAUSE 1.8 CARS OUT THERE FROM THE SAME ASSEMBLY PLANT MINE IS FROM WITH SAME ISSUES
Fuel/propulsion system, Apr 6, 2021
CAR FILING HARD, STALLING OUT WHEN ACCELERATING. COMPLETE STALL/FAILURE UNABLE TO RESTART WHILE DRIVING AT 55+ MPH. ALMOST GOT REAR ENDED. MORE ISSUES THE LESSGAS THE CAR HAS.
Fuel/propulsion system, Feb 25, 2021
THE FUEL GAUGE AND MILES TILL EMPTY IS ALWAYS WRONG SO I CONSTANTLY RUN OUT OF GAS WHILE DRIVING ANYWHERE. WHEN I PUT THE FUEL NOZZLE IN MY TANK IT MAKES A HISSING NOISE (COMPRESSED AIR) OR IT SPRAYS FUEL OUT OF THE TANK. I HAVE A CHECK ENGINE LIGHT THAT WON'T GO OFF.
Power train, Engine, Fuel/propulsion system, Jan 25, 2021
FORD TRANSMISSION PROBLEMS WONT GO AWAY!! TRANSMISSION SHUTTER AND POOR INITIAL ACCELERATION. THE CLUTCH HAS BEEN REPLACED TWICE AND TCM TWICE BY FORD DEALER. AFTER THE LAST TCM REPLACEMENT IN 2016 PROBLEMS CONTINUED AND I WAS TURNED AWAY BY FORD DEALERSHIPS BECAUSE NO ENGINE LIGHT CAME ON. NOW THAT FINALLY A CHECK ENGINE LIGHT CAME ON U0101, P07A3, I AM NOW OVER 100, 000 MILES THE CLUTCH IS NO LONGER COVERED UNDER WARRANTY BUT THE TCM IS. I HAVE HAD SEVERAL INCIDENTS WHERE THE CAR LOST ALL ACCELERATION ABILITIES WHILE DRIVING ON A BUSY HIGHWAY OR SIMPLY FAIL TO ACCELERATE AND A TRAFFIC LIGHT CAUSING MAJOR DELAYS FOR ANYONE AROUND ME. IT HAS BEEN A SAFTEY CONCERN FOR YEARS DUE TO THE UNPREDICTABILITY OF THE TRANSMISSION INTERMITTENTLY NOT ALLOWING ACCELERATION.