2007 Honda CR-V
Problems, recalls and owner-reported issues
Air bags is the leading concern among 887 owner complaints filed for this model year. This is the 5th highest complaint count among 26 CR-V model years with reports.
Of the 2007 reports, 34 involved a crash and 4 involved a fire. 23 people were injured and 1 person died.
What owners report most often
Recalls and investigations
Structure, frame and membersMar 30, 2023
Honda (American Honda Motor Co.) is recalling certain 2007-2011 CR-V vehicles that were sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Washington D.C., and Wisconsin. An accumulation of road salt may cause the frame to corrode and possibly detach the rear trailing arm.
A detached rear trailing arm can cause a loss of vehicle control, increasing the risk of a crash.
Dealers will inspect and install a support brace or repair the rear frame, as necessary, free of charge. Depending on the extent of any corrosion damage, Honda may offer to repurchase the vehicle. Owner notification letters were mailed May 22, 2023. Owners may contact Honda customer service at 1-888-234-2138. Honda's number for this recall is UE3.
Campaign 23V228000 on NHTSA.gov
Air bags, frontal, passenger side, inflator moduleJun 27, 2019
Honda (American Honda Motor Co.) is recalling certain 2009-2014 Acura TSX, 2011-2014 TSX Sport Wagon, 2010-2013 ZDX, 2008-2012 Honda Accord, 2010-2011 Accord Crosstour, 2006-2011 Civic and Civic Hybrid, 2008-2010 Civic GX NGV, 2012-2015 Crosstour, 2007-2011 CR-V, 2009-2013 Fit, 2014 Fit EV, 2010-2014 Insight, and 2009-2015 Pilot vehicles. The vehicles are equipped with passenger frontal air bag inflators assembled as a recall remedy part or replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Honda will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began August 12, 2019. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are F5F and Q5E.
Campaign 19V502000 on NHTSA.gov
Air bags, frontal, driver side, inflator moduleJun 27, 2019
Honda (American Honda Motor Co.) is recalling certain 2013 Acura ILX, 2015 RDX, 2005-2010 and 2012 RL, 2009-2014 TL, 2010 and 2012 ZDX, 2007-2011 CR-V, 2011-2013 and 2015 CR-Z, 2009-2013 Fit, 2013 Fit EV, 2010-2011 and 2013 Insight and 2007-2014 Ridgeline vehicles. These vehicles are equipped with driver frontal air bag inflators assembled as a recall remedy part or replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Honda will notify owners, and dealers will replace the driver frontal air bag inflator, free of charge. The recall began August 12, 2019. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are S5B and W59.
Campaign 19V500000 on NHTSA.gov
Air bags, frontal, passenger side, inflator moduleMay 16, 2019
Honda (American Honda Motor Co.) is recalling certain 2009-2014 Acura TSX, 2011-2013 TSX Sport Wagon, and 2010-2012 ZDX and 2008-2012 Honda Accord, 2010-2011 Accord Crosstour, 2006-2011 Civic, Civic Hybrid and Civic NGV, 2012-2014 Crosstour, 2007-2011 CR-V, 2009-2013 Fit, 2010-2013 Insight, and 2009-2015 Pilot vehicles. The front passenger air bag inflator may have been installed incorrectly during replacement.
An incorrectly installed air bag inflator may not properly deploy the passenger frontal air bag in the event of a crash, increasing the risk of injury.
Honda will notify owners, and dealers will inspect the inflator installation and, if necessary, replace the passenger frontal air bag module assembly, free of charge. The recall began July 5, 2019. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are M4O, P4R, T4Q, and W4P.
Campaign 19V378000 on NHTSA.gov
Air bags, frontal, driver side, inflator moduleMar 6, 2019
Honda (American Honda Motor Co.) is recalling specific 2003 Acura 3.2CL, 2013-2016 ILX, 2013-2014 ILX Hybrid, 2003-2006 MDX, 2007-2016 RDX, 2002-2003 3.2TL, 2004-2006, and 2009-2014 TL, 2010-2013 ZDX and 2001-2007 and 2009 Honda Accord, 2001-2005 Civic, 2003-2005 Civic Hybrid, 2001-2005 Civic GX NGV, 2002-2007 and 2010-2011 CR-V, 2003-2011 Element, 2007 Fit, 2002-2004 Odyssey, 2003-2008 Pilot, and 2006-2014 Ridgeline vehicles. The affected vehicles received a replacement driver air bag inflator as part of a previous Takata inflator recall remedy or a replacement driver air bag module containing the same inflator type as a service part. Due to a manufacturing error, in the event of a crash necessitating deployment of the driver frontal air bag, these inflators may explode.
An explosion of an inflator within the driver frontal air bag module may result in sharp metal fragments striking the driver, front seat passenger or other occupants resulting in serious injury or death.
Honda will notify owners, and dealers will replace the driver's air bag inflator with an alternate inflator, free of charge. The recall began April 10, 2019. Honda owners may contact customer service at 1-888-234-2138. Honda's number for this recall is O41. Acura owners may contact customer service at 1-888-234-2138. Acura's number for this recall is U40.
Campaign 19V182000 on NHTSA.gov
Air bags, frontal, passenger side, inflator moduleApr 26, 2018
Honda (American Honda Motor Co.) is recalling certain 2003-2012 Honda Accord and Pilot, 2010 Accord Crosstour, 2001-2011 Civic, 2002-2011 CR-V, 2003-2004, 2006-2008 and 2011 Element, 2007 and 2009-2013 Fit, 2010-2012 Insight, 2002-2004 Odyssey, and 2012 Ridgeline vehicles. The front passenger air bag may have been installed incorrectly during replacement.
An incorrectly installed air bag may deploy improperly in the event of a crash, increasing the risk of injury.
Honda will notify owners, and dealers will inspect and, if necessary, replace the passenger frontal air bag module assembly, free of charge. The recall began June 22, 2018. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are K1P, and M1O.
Campaign 18V268000 on NHTSA.gov
Air bags, frontal, passenger side, inflator moduleAug 31, 2017
Honda (American Honda Motor Co.) is recalling certain 2008-2012 Accord, 2010-2012 Accord Crosstour, 2006-2011 Civic, 2007-2011 CR-V, 2009-2012 Fit and Pilot, 2010-2012 Insight, and 2009-2012 Acura TSX vehicles that received replacement passenger frontal air bag inflators. One dealership may have incorrectly installed the replacement air bag inflators.
In the event of a crash, an incorrectly installed passenger frontal air bag inflator may deploy the air bag improperly, increasing the risk of injury.
Honda will notify owners, and dealers will replace the passenger frontal air bag module assembly, free of charge. The recall began October 30, 2017. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are O07, Y0A, N06, G05, M04, Y01, and O09.
Campaign 17V545000 on NHTSA.gov
Air bags, frontal, passenger side, inflator moduleJun 29, 2017
Honda (American Honda Motor Co.) is recalling certain 2007-2011 Honda CR-V vehicles which have had the passenger frontal air bag replaced. The air bag inflator repair kit may have been assembled by the supplier with an incorrect wire harness.
If an inflator with an incorrect wire harness is installed, the air bag may not deploy as intended, increasing the risk of injury in the event of a crash.
Honda will notify owners, and dealers will inspect and, if necessary, replace the passenger frontal air bag inflator, free of charge. The recall began on August 3, 2017. Owners may contact Honda customer service at 1-888-234-2138. Honda's number for this recall is KF9.
Campaign 17V417000 on NHTSA.gov
Air bags, frontal, passenger side, inflator moduleJan 10, 2017
Honda (American Honda Motor Co.) is recalling certain 2009-2012 Acura TSX, 2011-2012 Acura TSX Wagon, 2010-2012 Acura ZDX, 2008-2012 Honda Accord, 2010-2012 Honda Accord Crosstour and Honda Insight, 2009-2012 Honda Fit, 2009-2012 Pilot, 2007-2011 Honda CR-V, 2012 Honda FCX Clarity and 2006-2011 Honda Civic, Civic Hybrid, Civic NGV vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, if not included in "Zone A" above, Honda is recalling certain 2009 Acura TSX, Honda Fit and Pilot, 2008-2009 Honda Accord, 2006-2009 Civic, Civic Hybrid and Civic NGV, and 2007-2009 Honda CR-V vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, if not included in "Zone B" above, Honda is recalling certain 2008 Honda Accord, 2006-2008 Honda Civic, Civic Hybrid and Civic NGV and 2007-2008 Honda CR-V vehicles originally sold, or ever registered, in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Honda will notify owners, and dealers will replace the front passenger side air bag inflator, free of charge. The manufacturer has mailed an interim notification, and will send a second notification when parts are available. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are KE1 and KE2.
Campaign 17V030000 on NHTSA.gov
Air bags, frontal, passenger side, inflator moduleMay 24, 2016
Honda (American Honda Motor Co.) is recalling certain model year 2009-2011 Acura TSX, 2011 TSX Wagon, 2010-2011 Acura ZDX, 2008-2011 Honda Accord, 2010-2011 Accord Crosstour, 2006-2011 Civic, Civic Hybrid, and Civic GX, 2007-2011 CR-V, 2010-2011 FCX Clarity and Insight, and 2009-2011 Fit, and Pilot vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless already included in "Zone A" above, Honda is recalling certain model year 2008 Honda Accord, 2006-2008 Civic, Civic Hybrid and Civic GX, and 2007-2008 CR-V vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, the District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Honda will notify owners, and dealers will replace the inflator, free of charge. The recall began March 2017. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall is KA4, KA5, KA6, and KA7.
Campaign 16V346000 on NHTSA.gov
Air bags, frontal, driver side, inflator moduleFeb 3, 2016
Honda (American Honda Motor Co.) is recalling certain model year 2007-2011 Honda CR-V, 2011-2015 CR-Z, 2010-2014 FCX, and Insight, 2009-2013 Fit, 2013-2014 Fit EV, 2007-2014 Ridgeline, 2013-2016 Acura ILX, 2013-2014 Acura ILX Hybrid, 2007-2016 RDX, 2005-2012 Acura RL, 2009-2014 Acura TL, and 2010-2013 Acura ZDX vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.
In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Honda will notify owners, and dealers will replace the inflator, free of charge. The recall began March 2017. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are JY0, JY1, and JY2.
Campaign 16V061000 on NHTSA.gov
Power train, automatic transmission, control module (tcm/pcm/tecm)Aug 4, 2011
HONDA IS RECALLING CERTAIN MODEL YEAR 2005-2010 ACCORD, 2007-2010 CR-V, AND 2005-2008 ELEMENT PASSENGER CARS MANUFACTURED FROM JULY 1, 2004, THROUGH SEPTEMBER 3, 2010. THE OUTER RACE OF THE SECONDARY SHAFT BEARING MAY BE BROKEN DURING CERTAIN DRIVING STYLES. A BROKEN OUTER RACE MAY CAUSE ABNORMAL NOISE, THE MALFUNCTION INDICATOR LIGHT TO TURN ON, AND ALLOW CONTACT BETWEEN THE TRANSMISSION IDLE GEAR AND AN ELECTRONIC SENSOR HOUSING WITHIN THE TRANSMISSION.
THIS COULD RESULT IN A SHORT CIRCUIT CAUSING THE ENGINE TO STALL. ADDITIONALLY, BROKEN PIECES OF THE OUTER RACE OR BALL BEARING FROM THE SECONDARY SHAFT MAY BECOME LODGED IN THE PARKING PAWL RESULTING IN THE VEHICLE ROLLING AFTER THE DRIVER HAS PLACED THE GEAR SELECTOR IN THE PARK POSITION. ENGINE STALL AND UNEXPECTED VEHICLE MOVEMENT INCREASES THE RISK OF A CRASH OR PERSONAL INJURY TO PERSONS WITHIN THE PATH OF A ROLLING VEHICLE.
HONDA WILL NOTIFY OWNERS AND DEALERS WILL UPDATE THE AUTOMATIC TRANSMISSION CONTROL MODULE SOFTWARE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 27, 2011. OWNERS MAY CONTACT HONDA AUTOMOBILE CUSTOMER SERVICE AT 1-800-999-1009.
Campaign 11V395000 on NHTSA.gov
Representative owner complaints: structure
77 reports, newest first. Show all
Structure, Sep 2, 2026
Vehicle Affected: 2007 Honda CR-VRelated Recall: NHTSA Recall Campaign Number 23V228000 (Rear Frame Stiffener Brackets)Description of Incident:I am reporting a severe safety issue regarding how a Honda dealership and American Honda Motor Co. are executing Safety Recall 23V228. I presented my vehicle to an authorized Honda dealer for the rear frame rust inspection. (Lundgren Honda of Auburn MA) The technician "passed" the vehicle and offered to install the remedy support brace because the specific trailing arm bolt hole could technically receive a bolt. However, the dealer completely ignored a catastrophic structural failure directly adjacent to the recall site. The actual boxed structural frame rail just one inch above the bolt hole has completely disintegrated, leaving giant holes and heavily flaking, hollowed-out metal. Per Honda's official recall service bulletin instructions, the reinforcement brace must be securely anchored to structurally sound frame metal. Slapping a bracket onto a tiny piece of metal while the supporting frame rail above it is entirely gone creates an extreme liability and does not fix the safety risk of a suspension collapse. I contacted Honda Corporate Customer Support to escalate this. Despite providing clear photographic proof that the structural integrity of the frame rail is gone, Honda is giving me severe pushback and delaying action on my open case file. They are ignoring a severe structural failure at the exact recall site to avoid their legal obligation for a vehicle buyback. The vehicle remains an immediate highway hazard. I have attached photographic evidence showing the gaping hole in the frame rail directly next to the recall bolt location. The car would not pass a safety inspection from a MA State inspection facility, and they refused to sticker it, or put tires on it....
Structure, Aug 17, 2026
The contact owns a 2007 Honda CR-V. The contact stated that there was corrosion and frame rust on the vehicle caused by road salt and moisture, which caused the rear of the vehicle to collapse. The contact associated the failure with NHTSA Campaign Number: 23V228000 (Structure). The dealer was contacted and referred the contact back to the dealer who repaired the vehicle under the recall. The manufacturer was made aware of the failure. The failure mileage was approximately 258,000.
Suspension, Structure, Wheels, Jan 3, 2026, crash
There was a safety recall for the rear arm control and excessive rust, Honda said they fixed it back in 2018… out of no where my car lost control and caused me to crash, I brought the car back to Honda and the rear arm bracket broke off due to excessive rust however Honda states it was repaired and there is nothing they can do, they won’t even look at the vehicle.
Structure, Oct 17, 2025
I am writing to formally express my dissatisfaction regarding the handling of the recall for my 2007 Honda CR-V due to frame corrosion. During the recall service, only a bracket was installed under the wheel well, addressing a single area despite extensive rust present throughout the frame and underbody. I believe the vehicle should have been considered for a buyback rather than a limited repair. Recently, my vehicle failed its safety inspection due to a rust hole in the frame, making it unsafe to drive and only suitable for scrap. When I contacted Honda for further assistance, I was informed that only recall-related issues would be addressed, and no additional support was offered. The presence of severe rust and a compromised frame poses significant safety risks, including: •Increased likelihood of structural failure in the event of a collision, which could result in serious injury or death. •Reduced effectiveness of critical safety components, such as seat belts and airbags, due to weakened mounting points. •Higher risk of suspension or wheel detachment while driving, potentially causing loss of vehicle control. I am deeply concerned about the safety implications and the inadequate resolution of the recall.
Structure, Aug 12, 2024
The contact owns a 2007 Honda CR-V. The contact stated while driving at an undisclosed speed, the contact heard a loud clanking sound coming from the rear of the vehicle. There were no warning lights illuminated. The vehicle was taken to the dealer where the vehicle was diagnosed and determined that the subframe was completely rotted. The contact was informed that the vehicle could not be repaired. The contact was also informed that the vehicle was unsafe to drive. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 188,000.
Structure, Mar 12, 2024
See attached document for complaint
Structure, Feb 11, 2024
On 07/21/2023, I took my car to the dealership for an evaluation related to a recall on the Rear Frame Brace. The inspection revealed that my car was unsafe to drive, and I was informed that I could not take it off the dealership premises. Since then, I have been trying to reach an agreeable solution with America Honda Motor- Honda Recall, but they have not responded. I have also tried to get assistance from the Attorney General of my state but to no avail. The local Honda dealership still has possession of my auto, and this issue remains unresolved as of 02/11/2024.
Structure, Jan 2, 2024
The contact owns a 2007 Honda CR-V. The contact stated that the vehicle was taken to the dealer to be repaired under NHTSA Campaign Number: 23V228000 (Structure). The contact was informed that the dealer was unable to perform the recall repair due to a screw that had sealed due to corrosion. The dealer contacted the manufacturer. The manufacturer stated that since the screw was not able to be removed, to leave the screw as-is and the vehicle was still able to be driven. The contact had not spoken to the manufacturer. The failure mileage was 116,000.
Suspension, Structure, Dec 7, 2023
The contact owns a 2007 Honda CR-V. The contact stated while driving 25 MPH, the rear passenger's side of the vehicle collapsed inadvertently. The contact was able to pull to the side of the road. The contact noticed that the rear passenger's side wheel had detached and rotated 90 degrees into the wheel well. The vehicle was towed to an independent mechanic, who determined that the failure was related to NHTSA Campaign Number: 23V228000 (Structure). The vehicle was then towed to the dealer, where it was determined that the vehicle had failed the recall inspection test. The dealer informed the contact that the vehicle was beyond repair and could be repurchased by the manufacturer per the recall remedy. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and a case was opened; however, no further assistance was provided. The failure mileage was approximately 190,000. Parts distribution disconnect.
Structure, Nov 15, 2023, crash
The contact owned a 2007 Honda CR-V. The contact stated while driving at approximately 35 MPH, steering functionality was lost and drove off the road into a ditch. The contact stated no warning light was illuminated. The contact stated that there was no damage to the vehicle and the contact was unhurt. The contact had the vehicle towed to a body shop where it was diagnosed that the rear axle had separated from the frame due to severe corrosion of the rear supports. The vehicle was not repaired. The contact sold the vehicle for scrap. The contact had received notification of NHTSA Campaign Number: 23V228000 (Structure) and related the failure to the notification. The manufacturer was informed of the failure. The failure mileage was approximately 230,000.
Structure, Oct 13, 2023
The contact owns a 2007 Honda CR-V. The contact stated that while his wife was at a complete stop, the vehicle jerked upon acceleration with the Traction Control Malfunction warning light illuminated. The contact’s wife pulled over and discovered that the rear driver’s side tire was inverted inside the wheel well. Due to the failure, the vehicle was towed to a dealer where the contact was informed that the vehicle was included in NHTSA Campaign Number: 23V228000 (Structure). Despite the recall, the vehicle remained in the possession of the dealer due to the part not being available. The manufacturer was also notified of the failure. The vehicle was not yet repaired. The failure mileage was approximately 212,000.
Structure, Aug 24, 2023
The contact owns a 2007 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
Structure, Aug 2, 2023
The contact owns a 2007 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
Structure, Jul 13, 2023
The contact owns a 2007 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure); however, the part to do the recall repair was not yet available. The local dealer and other unknown dealers were notified of the issue. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
Structure, Jul 12, 2023
The contact owns a 2007 Honda CR-V. The contact stated that the vehicle was taken to the dealer to be repaired under NHTSA Campaign Number: 23V228000 (Structure); however, the dealer was unable to fix the vehicle due to the extreme corrosion on the subframe. Additionally, the dealer informed the contact that Honda would offer a buyback of the vehicle. The manufacturer was made aware of the failure and opened a case. The failure mileage was unknown.
Structure, Jun 12, 2023
The contact owns a 2007 Honda CR-V. The contact stated while driving 50 MPH, an unknown component detached from the vehicle and the vehicle began to steer to the right independently. The contact stated that the Traction Control Malfunction warning light was illuminated. The contact continued driving to her destination. A dealer was not contacted. The vehicle was taken to an independent mechanic to be diagnosed. The contact was informed that the control arms, tie rods, sway bars, engine control unit (ECU), and the steering gear assembly needed to be replaced. The vehicle was repaired. The contact stated that on another occasion while driving, an unknown component detached from the vehicle. The contact stated that the Traction Control Malfunction warning light was illuminated. The vehicle was driven to the residence and parked. The vehicle was not drivable. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) and associated the previous failures with the recall. The contact called the local dealer and was informed to drive or tow the vehicle to their location to have the vehicle diagnosed. The vehicle was not diagnosed or repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 180,000.
Structure, Apr 26, 2023, crash
The contact owns a 2007 Honda CR-V. The contact stated that while driving at an undetermined speed the rear suspension detached from the frame and drove into a ditch. There were no warning indicator lights illuminated. The vehicle was towed to the contact's residence. The contact called the local dealer. The vehicle was not diagnosed or repaired. There were no reported injuries, air bag deployment, fire or police reports filed. The manufacturer was not contacted. The failure mileage was approximately 182,000. The contact stated the failure was related to the NHTSA Campaign Number: 23V228000 (Structure).
Structure, Apr 24, 2023
The contact owns a 2007 Honda CR-V. The contact stated that while driving at 60 MPH, the rear driver's side control arm detached from the rear sub frame. The vehicle was towed to a motel and then to the residence. The dealer was made aware of the failure; however, the vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and a case was opened. The contact was later made aware of NHTSA Campaign Number: 23V228000 (Structure) from the news media for which the VIN was included. The failure mileage was approximately 200,000.
Structure, Apr 13, 2023
The contact owns a 2007 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that while driving at various speeds, an abnormal sound was coming from the vehicle. There was no warning light illuminated. The vehicle was taken to an independent mechanic who confirmed the corrosion failure and linked that failure to the recall. The failure mileage was approximately 210,000. VIN tool confirms parts not available.
Structure, Apr 11, 2023
The contact owns a 2007 Honda CR-V. The contact stated that while stopped at a stop sign, the rear passenger’s side subframe detached. The contact related the failure to NHTSA Campaign Number: 23V228000 (Structure). The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 187,000.
Structure, Jan 14, 2023
Passenger side rear door lock stuck in locked position Passenger in rear can not get out of vehicle Have not taken to dealer
Structure, Engine, Oct 6, 2022
My catalytic converter was stolen when my car was parked. Honda owners has been targeted for its catalytic converters, and there are numerous reports of Honda’s cats being stolen. Honda has a major defect where it makes it easier for thieves to steal the cat in minutes. There are 3 major flaws with the product. 1) Hondas don’t automatically come with a cat converter steel shield, cage, or other protector to make them harder to steal. 2) Hondas don’t install their cat in the engine compartment like other car manufacturers to deter theft. 3) Honda’s cat contains valuable materials, which is why they are targeted. Other car brands tend to have less valuable catalysts so thieves are not incentivized to steal them. Because there are many cats being stolen, there is a shortage to replace them, and car owners have to wait weeks to months to get their cat replaced. It’s been almost 2 weeks, and my car is still at the mechanic’s waiting for a replacement catalytic converter. My safety, and the safety of my family, including two kids, were compromised because I had to drive my family home (and we live in a hilly area) without a cat as it was stolen Sunday evening, and I had to wait until the next day to get it to the mechanic’s. The warning light appeared when I started the car, but by the telltale sound my car made, I already knew the cat was stolen. A police report was filed and the claim with my insurance was completed. Cats are very expensive to replace and an inconvenience for a 1-car family. Now we don’t have a car to do basic necessities like take the kids to school, go grocery shopping for the family, go to work, and go to doctor appointments.
Suspension, Structure, May 24, 2022
While performing maintenance on the car, I found that the left (drivers) rear mounting bracket which is a part of the frame/body, and hold the right rear trailing arm - holding the rear axle was severely rusted and cracking apart from corrosion. The right (passenger) bracket showed no rust damage. This problem has been reported by others, and Canada has found the same issues and issued a recall for this car/vin group. Although this car is 15 years old, this thick 3/8" heavy metal bracket should not have disintegrated like this even with the salt used on the highways, and is shown with absolutely no issue with the right (passenger side)bracket. Upon taking it to the dealer, there was nothing they could do, nor could they get the "fix" being used in Canada or any other information as to how they are correcting this problem. Suggestion is to buy a new car or take it to a body shop and see if they could fabricate a repair. Honda dealer did not seem to be too concerned about this rust, so I will have to go elsewhere to have it evaluated. From what I have found here on the internet, this is a serious problem, and when it breaks as it has for others, you loose control of the car because the axle is now only attached to one side of the car. If there is a fix for this, (as they have one in Canada) they should be compelled to provide it. This isn't a who pays for the repair. It's been known for some time now, and they should have already addressed this. But to withhold the safety fix isn't acceptable.
Suspension, Structure, Jul 15, 2021
While driving vehicle on 07/01/2021 the right rear trailing arm disconnected from the right rear frame rail due to corrosion. Transport Canada issued a recall (#2019-025) for 83,953 Honda CR-V's sold new in Canada for this problem. My Honda CR-V was manufactured at the same plant as those recalled in Canada. The reason for the recall in Canada was because these vehicles were driven on roads treated with deicing materials, much the same as vehicles driven in Illinois. This vehicle has not been inspected by American Honda. This is a clear safety issue due to the nature of the suspension becoming detached with no notice.
Suspension, Structure, Sep 23, 2020
AS I WAS DRIVING DOWN A CITY STREET, THE RIGHT REAR SUSPENSION CONTROL ARM CAME LOOSE FROM THE FRAME. THE RIGHT WHEEL TIRE SUBSEQUENTLY BECAME LODGED AGAINST THE REAR OF THE WHEEL WELL AT AN ANGLE. I WAS ABLE TO MANEUVER THE CAR TO THE SIDE OF THE ROAD. POLICE ARRIVED TO BLOCK OFF THE NEAREST LANE SO I COULD SAFELY BE TOWED FROM THE SCENE, AS THE CAR WAS UNDRIVABLE. I AM FORTUNATE THAT THIS DID NOT HAPPEN AT HIGH SPEED, AS I DO NOT BELIEVE I WOULD HAVE SAFELY BEEN ABLE TO MAINTAIN CONTROL OF THE VEHICLE. THE CONTROL ARM CAME LOOSE DUE TO EXCESSIVE RUST ON THE FRAME. THE AREA AROUND THE MOUNTING LOCATION FOR THE ARM IS TORN AWAY FROM THE FRAME, THE NUTS AND BOLTS ARE STILL ATTACHED TO THE FRAGMENTS OF FRAME THEY WERE ORIGINALLY MOUNTED TO. THIS MODEL YEAR CRV IS UNDER RECALL FOR EXCESSIVE CORROSION IN CANADIAN PROVINCES WHERE ROAD SALT IS EXTENSIVELY USED IN WINTER. THIS MODEL WAS PURCHASED IN MINNESOTA, WHERE ROAD SALT IS EXTENSIVELY USED IN WINTER.