2012 Jeep Wrangler
Problems, recalls and owner-reported issues
Power train is the leading concern among 833 owner complaints filed for this model year. This is the 5th highest complaint count among 26 Wrangler model years with reports.
Of the 2012 reports, 22 involved a crash and 19 involved a fire. 22 people were injured and 2 people died.
What owners report most often
Recalls and investigations
Seat belts, front, anchorageSep 26, 2019
Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.
A separated or severed seat belt buckle strap will result in an inoperable seat belt, increasing the risk of injury in the event of a crash.
FCA US will notify owners, and dealers will replace the driver's seat belt buckle, free of charge. Interim notices informing owners of the safety risk were mailed November 19, 2019. Owners will received a second letter and the recall began March 26, 2020. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is VA6.
Campaign 19V680000 on NHTSA.gov
Air bags, frontal, passenger side, inflator moduleDo not drive until repairedJan 15, 2019
Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.
In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.
Campaign 19V018000 on NHTSA.gov
Air bags, frontal, passenger side, inflator moduleDo not drive until repairedJan 9, 2018
Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.
Campaign 18V021000 on NHTSA.gov
Air bags, frontal, passenger side, inflator moduleDo not drive until repairedMay 24, 2016
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.
These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.
Campaign 16V352000 on NHTSA.gov
Air bags, frontal, driver side, inflator moduleMay 11, 2016
Chrysler (FCA US LLC) is recalling certain model year 2011-2016 Right Hand Drive Jeep Wrangler vehicles manufactured February 16, 2010, to May 2, 2016. The clockspring assembly may become contaminated with dust and cause the air bag circuit to fail.
Failure of the air bag circuit may prevent the driver's frontal air bag from deploying in the event of a crash, increasing the risk of injury.
Chrysler will notify owners, and dealers will replace the clockspring, wheel back cover, and column shroud, free of charge. The recall began on August 11, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S40.
Campaign 16V288000 on NHTSA.gov
Electrical systemOct 8, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2013 Jeep Wrangler vehicles manufactured February 16, 2010, to July 19, 2013. Corrosion in the exterior heated power mirror electrical connector may result in an electrical short.
An electrical short increases the risk of a fire.
Chrysler will notify owners, and dealers will move the exterior mirror power feed to a separate connector, free of charge. Chrysler issued an interim notification to owners on December 8, 2014. The recall began on March 3, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P61.
Campaign 14V631000 on NHTSA.gov
Steering, hydraulic power assist, hose, piping, and connectionsJun 4, 2013
Chrysler Group LLC (Chrysler) is recalling certain model year 2012-2013 Jeep Wrangler vehicles equipped with a 3.6L engine and an automatic transmission and manufactured January 23, 2011, through February 23, 2013. The power steering line may contact and wear a hole in the transmission oil cooler line resulting in a loss of transmission fluid.
A loss of transmission fluid may result in a loss of transmission function which may increase the risk of a crash.
Chrysler will notify owners, and dealers will replace the power steering return tube assembly, free of charge. The recall began on September 23, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N28.
Campaign 13V234000 on NHTSA.gov
Air bagsMay 7, 2013
Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 Jeep Wrangler right-hand drive vehicles manufactured February 1, 2007, through October 10, 2011. The affected vehicles have airbag clockspring assemblies that could experience broken airbag circuits.
In the event of a crash necessitating airbag deployment, a broken electrical circuit in the airbag clockspring wiring assembly can lead to non-deployment of the driver-side frontal airbag and will not be able to properly protect the driver, increasing the risk of injuries.
Chrysler will notify owners, and dealers will replace the clockspring and add a steering wheel dust shield, free of charge. The recall began on June 10, 2013. Owners may contact Chrysler at 1-800-247-9753. This recall supercedes NHTSA recall 11V-528. Chrysler's recall campaign number is M31.
Campaign 13V176000 on NHTSA.gov
EquipmentFeb 25, 2013
Quadratec, Inc. is recalling certain aftermarket accessory, driver-side, Ultimate Floor Liners part numbers 14254.0301 07, 14254.0301 08, 14254.0301Q, 14254.0302 07, 14254.0302 08, 14254.0302Q, 14254.0303 07, 14254.0303 08, 14254.0303Q, 14254.0309 07, 14254.0309 08, and 14254.0309Q sold from May 1, 2012, through February 14, 2013. The liners are for use in 2007-2013 Jeep Wranglers. The anchor point for the affected floor liners may tear during use, particularly when exposed to high temperatures. The tearing may allow the floor liner to shift forward.
If the liner shifts forward it may impede the operation of the accelerator and possibly lead to unintended acceleration, which may increase the risk of a crash.
Quadratec will notify owners and either exchange the liners or provide them with a hook guard kit to help secure the driver-side mat, free of charge. The recall began on April 4, 2013. Owners may contact Quadratec at 1-800-463-2998 or info@quadratec.com.
Campaign 13E010000 on NHTSA.gov
Air bags, frontalNov 2, 2011
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2008-2012 RIGHT HAND DRIVE (RHD) JEEP WRANGLER VEHICLES MANUFACTURED FROM FEBRUARY 1, 2007, THROUGH OCTOBER 10, 2011. SOME VEHICLES MAY BE EQUIPPED WITH DRIVER'S AIRBAG CLOCKSPRING ASSEMBLIES THAT COULD EXPERIENCE A COMPROMISED AIRBAG CIRCUIT RESULTING IN AN AIRBAG LAMP ILLUMINATION, WHICH INDICATES THAT THE AIRBAG MAY NOT DEPLOY.
A BROKEN ELECTRICAL CIRCUIT IN THE AIRBAG CLOCKSPRING WIRING ASSEMBLY CAN LEAD TO NON-DEPLOYMENT OF THE DRIVER FRONTAL AIRBAG AND WILL NOT BE ABLE TO PROPERLY PROTECT THE DRIVER IN THE EVENT OF A CRASH, INCREASING THE RISK OF INJURIES.
CHRYSLER WILL NOTIFY OWNERS AND REMEDY THE VEHICLES AS NECESSARY FREE OF CHARGE. CHRYSLER WILL MAIL TO OWNERS AN INTERIM NOTIFICATION DURING MARCH 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Campaign 11V528000 on NHTSA.gov
Representative owner complaints: engine
178 reports, newest first. Show all
Engine, Jul 7, 2026
The engine's cylinder head/valve train has failed internally, allowing combustion gases to enter the cooling system — confirmed via a chemical block test performed by a master automotive technician on November 29, 2024, which verified combustion gases present in the coolant. This is a widely documented defect on this engine and model year, related to valve seat erosion in the cylinder head. Symptoms first appeared in June 2018 as an unusual higher-pitched, stressed sound from the engine. Over time this progressed to recurring, confirmed misfires on cylinders 1, 2, 3, and 5 (diagnostic codes P0300, P0301, P0302, P0303, P0305) and a mixture control fault (P219B). The check engine light has intermittently stayed illuminated for months at a time, then gone off for extended periods while the same fault codes remain stored and confirmed by a diagnostic scanner — currently the light is off but the codes persist. The vehicle frequently runs rough enough that the engine must be turned off and restarted to temporarily return to closer-to-normal operation. Noticeable vibration is felt during much of this pattern. Spark plugs, ignition coils, oxygen sensors, and the PCV valve have all been inspected/replaced and ruled out as the cause on multiple occasions over more than a year, isolating the cause to the cylinder head itself. This creates a driveability and potential stalling/hesitation risk, though no crash, injury, or fire has occurred to date. The vehicle has not been formally inspected by the manufacturer, police, or an insurance representative. The affected component remains in the vehicle and is available for inspection upon request.
Engine, Engine and engine cooling, Apr 1, 2026
The contact owns a 2012 Jeep Wrangler. The contact stated that while driving at 20 MPH, the check engine warning light illuminated. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The vehicle was taken to an independent mechanic, where a scan was completed, and diagnostic trouble codes for the Emissions, engine misfire, timing chain, and crank position sensor failures were displayed. The manufacturer was not contacted. The failure mileage was approximately 71,756.
Electrical system, Air bags, Engine, Mar 26, 2026
My complaint is that I was sold a dangerously defective vehicle with a known, unrepaired “stop driving” airbag safety recall, was not warned about the deadly risk, and am now being told to move and tow the car in direct contradiction to official safety instructions. ### Factual background - The vehicle I purchased has a Takata‑type airbag safety recall that carries a formal “do not drive” or “stop driving” warning because the airbag can explode and kill or severely injure occupants, even in a minor crash.[1][2][3][4] - Federal safety authorities have confirmed that at least 28–29 people in the United States have been killed and more than 400 injured by exploding Takata airbag inflators.[3][4][5][1] - I received the recall notice about two months ago, but I was told the repair parts were back‑ordered, which delayed fixing the deadly defect through no fault of my own.[1][3] - During this delay, the vehicle’s battery became completely dead, and I am now being told by the recall and towing company that I must make sure the car is taken out of the garage, which would require entering and moving a vehicle I have been legally and explicitly told not to drive. ### Legal and safety concerns - Official guidance from the National Highway Traffic Safety Administration (NHTSA) and the manufacturer is that vehicles under this Takata “do not drive” recall must not be driven at all until the defective airbag is replaced, because even a minor collision can cause the inflator to explode and send metal shrapnel into the cabin.[2][4][3][1] - The instruction to move or drive the car out of the garage conflicts with this clear safety warning and effectively asks me to assume a risk that has already caused multiple deaths and serious injuries nationwide.[4][5][2][3][1] - Federal law prohibits franchised dealers from selling new vehicles with unrepaired safety recalls, and legal experts warn that selling used vehicles with undisclosed safety defects can expose sellers and dealers to
Engine, Oct 29, 2025
The vehicle exhibits a persistent valvetrain ticking noise associated with the rocker/lifter/cam components of the 3.6L Pentastar V6. The engine makes a rhythmic metallic tapping at idle and during acceleration. The noise has progressively worsened, leading to rough idle and occasional misfires. This issue is documented in multiple Stellantis technical service bulletins (e.g., TSB 09-015-24 and TSB 09-011-25) which attribute the noise to hydraulic lash adjuster and cam/rocker wear. If unaddressed, the failure can cause camshaft damage, metal debris contamination, loss of power and potential engine stall, posing a safety risk. The vehicle is available for inspection. The problem has been confirmed by independent mechanics who recommend replacement of the rocker arms, lifters and camshaft to prevent catastrophic engine failure.
Engine, Sep 30, 2025
The vehicle exhibits a persistent valvetrain ticking noise associated with the rocker/lifter/cam components of the 3.6L Pentastar V6. The engine makes a rhythmic metallic tapping at idle and during acceleration. The noise has progressively worsened, leading to rough idle and occasional misfires. This issue is documented in multiple Stellantis technical service bulletins (e.g., TSB 09-015-24 and TSB 09-011-25) which attribute the noise to hydraulic lash adjuster and cam/rocker wear. If unaddressed, the failure can cause camshaft damage, metal debris contamination, loss of power and potential engine stall, posing a safety risk. The vehicle is available for inspection. The problem has been confirmed by independent mechanics who recommend replacement of the rocker arms, lifters and camshaft to prevent catastrophic engine failure.
Engine, Aug 31, 2025
Timing chain and misfire bank 1 and bank 2 crank shaft and crank sensor issues.
Engine, Jun 6, 2025
I am reporting a persistent and safety-relevant defect in my 2012 Jeep Wrangler with the 3.6L Pentastar engine. The vehicle is experiencing misfires on multiple cylinders, especially cylinders 1 and 5, triggering codes P0300, P0301, and P0305. These misfires result in loss of power, hesitation, and rough idle, creating serious safety concerns during acceleration or highway driving. Despite replacing spark plugs, ignition coils, the crankshaft position sensor, purge valve, and both oxygen sensors, the problem continues. The vehicle has just 83,000 miles and is currently at a certified third-party repair facility. Multiple mechanics believe the issue stems from known defects in the left (Bank 1) cylinder head or valve train components—an issue Chrysler previously acknowledged via TSBs and a 10yr/150k mile extended warranty on select VINs. I contacted Jeep Cares and requested goodwill support, but they refused to even discuss the issue because my Jeep is not at a dealership. This leaves owners like me with limited, expensive options despite being affected by a well-documented defect. Jeep forums and independent shops have seen widespread misfire problems on early 3.6L Pentastar engines, especially 2012-2013 models. I urge NHTSA to investigate this pattern of failure. The misfires impact driveability and safety, and the manufacturer has not offered sufficient resolution or consistent support to affected customers. I’m happy to provide additional information, documentation, or diagnostics.
Engine, Jan 30, 2025, fire
Engine spontaneously caught fire. It had been parked for hours before it happened. Everything under the hood was totaled
Service brakes, Air, Traction control system, Engine, Oct 15, 2024
The contact owns a 2012 Jeep Wrangler. The contact stated that while operating the vehicle the ABS, Traction Control and check engine warning lights had remained illuminated. The contact indicated that while pressing the brake pedal to stop, the brake pedal extended to the floor causing the braking distance to become extended. The vehicle was taken to the local dealer who diagnosed that the ABS module was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure but no assistance was offered. The failure mileage was 55,000.
Engine, Jan 4, 2024
In my 2012 Jeep I had to replace the engine and catalytic converters. The engine number 3 cylinder failed due to excessive ware causing lower compression. After the engine (long block) was replaced, one of the cylinders was miss firing. This miss firing was traced to micro cracks in the plastic/composite intake manifold (original and not part of the engine replacement). Because these micro cracks changed the fuel air ratio on specific cylinders by leaning out the cylinders near the cracks this lean mixture would cause the affected cylinders to run hot that would lead to both the excessive ware on the one cylinder and would comprise the catalytic converters. Because this change in fuel air mixture was caused by the intake manifold and Jeep does not have any inspection requirements or methods for this item and even after the Jeep Dealer did a full diagnosis using their factory specified equipment the issue with the manifold was not found. My local AMMCO shop found the cracking in the manifold that was the route cause of the problem.
Engine, Dec 28, 2023
Jeep Wrangler 3.6 liter 90k miles lifter making loud noise. Seems you had a recall about this on the 2012 and guess I missed out
Engine, Oct 11, 2023
6 days after an oil change, the temp gauge while driving went from cool to hot in under a mile and the engine temp light came on. There was coolant all over the underside of the car it was near catastrophic. I had to have it towed to the dealership for repairs. The faulty part was the oil filter adapter it was cracked by over tightening of the oil filter.
Power train, Engine, Fuel/propulsion system, Apr 4, 2023
Engine Stalls Randomly while Driving. Will crank over several times and over approx 10-15 min. of cranking(Say every 3-5min) vehicle will and will restart. No check engine lights and no warning. The loss of power can be dangerous since brake and steering assist require engine to be running. Vehicle will be fine for several days local commute and problem will recur without warning, usually on longer commute. Vehicle is unsafe and unpredictable.
Engine, Dec 7, 2022
CAM SENSOR FAILED. CHECK ENGINE LIGHT AND TRACTION CONTROL LIGHT APPEARED. REPLACED AND SAME PROBLEMS OCCURRED. MAY BE WIRING OR CAM/ROCKER ISSUES.
Engine, Nov 17, 2022
The contact owns a 2012 Jeep Wrangler. The contact stated while starting the vehicle, there was an abnormal burning odor around the vehicle. The contact stated while driving 45 MPH and other various speeds the burning odor was still present. The check engine warning light illuminated with the temperature gauge rising from normal to hot. An audible alarm was heard during the failure. The vehicle was driven to the residence and then towed to a dealer. The vehicle was diagnosed and determined that the radiator needed to be replaced. The contact had the vehicle towed to an independent mechanic who determined that coolant was leaking into the cylinder head. The vehicle had not been repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 60,000.
Power train, Engine, Jul 12, 2022
While driving the car randomly stalls. I lose power steering and braking. The car will not restart. This issue has been recorded by the dealer. The vehicle was last inspected on July 5th. I have been issued a Jeep Care case manager, case # 82963828. There are no warnings, while driving makes a left-hand turn the car just stalls!
Power train, Electrical system, Engine, Jul 4, 2022
While driving making a turn, shifting from 1st to 2nd gear, and vehicle stalls losing all power. I had a crank no-start scenario! The vehicle has been to the dealer multiple times and the issue can not be duplicated. The vehicle has been inspected multiple times and there are no known issues. No-fault codes are thrown. I was able to cost to a safe location, and wait. after 3-5 min the vehicle restarted.
Power train, Electrical system, Engine, Jul 4, 2022
While driving making a turn, shifting from 1st to 2nd gear, and vehicle stalls losing all power. I had a crank no-start scenario! The vehicle has been to the deal multiple times and the issue can not be duplicated. The vehicle has been inspected multiple times and there are no known issues. No-fault codes are thrown. I was able to cost to a safe location, and wait. after 3-5 min the vehicle restarted.
Power train, Engine, Fuel/propulsion system, Jul 4, 2022
While driving making a turn, shifting from 1st to 2nd gear, and vehicle stalls losing all power. The vehicle has been to the deal multiple times and the issue can not be duplicated. The vehicle has been inspected multiple times and there are no known issues. No-fault codes are thrown. I stalled in the middle of a busy intersection, with my children in the car. I had to push the vehicle to safety!
Power train, Electrical system, Engine, Jul 4, 2022
Starting out at a stop sign. engaging the clutch to start moving, while shifting into 2nd gear while turning the vehicle stalls. Losing all power steer and brakes. I try to re-start the car i get a crank no-start scenario. Wait 3-5 min, retry starting the vehicle starts.
Power train, Electrical system, Engine, Jul 4, 2022
Starting out at a stop light, engaging the clutch to start moving, I depressed the clutch to shift into second gear while making a turn, the vehicle stalls, losing all power.
Engine, Jun 26, 2022, fire
I was driving on the highway and the engine caught fire. I’ve been looking for an engine to rebuild and all of them had previously been on fire. I believe the engine is defective for the jeeps that year, make and model.
Power train, Engine, Fuel/propulsion system, May 28, 2022
While driving the car stalled. Loss of power steering and braking. I was able to coast to a safe location. I tried to restart, but Crank- No Start.
Power train, Electrical system, Engine, May 2, 2022
Random Stalling while driving, making a left-hand turn. While entering an intersection, the vehicle stalled losing all power. Was able to coast to a safe spot. Waited 15 min, the vehicle started. No check engine light.
Power train, Engine, Fuel/propulsion system, May 2, 2022
While crossing an intersection the vehicle stalled for no reason. No Codes were posted. Crank No Start, waited 10 min, and the vehicle started. Drove to the dealer to resolve. Dealer has no known reason for stalling while driving