2018 Jeep Wrangler
Problems, recalls and owner-reported issues
Steering is the leading concern among 1,822 owner complaints filed for this model year. This is the highest complaint count among 26 Wrangler model years with reports.
Of the 2018 reports, 22 involved a crash and 25 involved a fire. 13 people were injured.
What owners report most often
Recalls and investigations
Back over prevention, sensing system, cameraSep 12, 2024
Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."
A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.
Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 77B.
Campaign 24V676000 on NHTSA.gov
Electrical system, instrument cluster/panelSep 5, 2024
Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."
An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.
Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 30B.
Campaign 24V652000 on NHTSA.gov
Power train, clutch assemblyFeb 23, 2023
Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Dealers will replace the clutch assembly and update the software, free of charge. Owner notification letters were mailed from November 16, 2023 through July 25, 2024. Owners may contact (FCA US, LLC) customer service at 1-800-853-1403. FCA US LLC's number for this recall is 19A. This recall expands and replaces previous recall 21V-028. Vehicles previously repaired under recall 21V-028 will need to have the new remedy completed.
Campaign 23V116000 on NHTSA.gov
Power train, clutch assemblyJan 28, 2021
Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
FCA US LLC will notify owners, and dealers will add software to reduce engine torque capability when clutch assembly temperatures rise to a level that may damage the inner pressure plate, free of charge." FCA has ordered a stop sale for the affected vehicles as of February 25, 2021. Owner notification letters were mailed on March 4, 2021.
Campaign 21V028000 on NHTSA.gov
Power train, clutch assemblyMar 3, 2020
Chrysler (FCA US LLC) is recalling certain 2018-2020 Jeep Wrangler and 2020 Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
The overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Chrysler will notify owners, and dealers will reroute a wire harness and inspect the clutch system, and replace components as needed. The recall began April 30, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W12.
Campaign 20V124000 on NHTSA.gov
Seat belts, front, anchorageSep 26, 2019
Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.
A separated or severed seat belt buckle strap will result in an inoperable seat belt, increasing the risk of injury in the event of a crash.
FCA US will notify owners, and dealers will replace the driver's seat belt buckle, free of charge. Interim notices informing owners of the safety risk were mailed November 19, 2019. Owners will received a second letter and the recall began March 26, 2020. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is VA6.
Campaign 19V680000 on NHTSA.gov
EquipmentApr 23, 2019
Erwin Hymer Group USA LP dba American Fastbacks (EHGUSA-AF) is recalling certain 2018 Jeep Wrangler vehicles sold with a roof top tent installed. The top cover of the roof top tent may crack or break, possibly resulting in the cover detaching from the vehicle while moving.
If the roof top tent cover detaches from the vehicle while moving, it can create a road hazard, increasing the risk of a crash.
The remedy for this recall is still under development. The recall began May 9, 2019. Owners may contact American Fastbacks customer service at 1-844-533-7997 extension 301. Note: Vehicles in this recall are also included in recall 19V-190.
Campaign 19V320000 on NHTSA.gov
Latches/locks/linkages, doors, latchNov 8, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler four-door vehicles. The right rear passenger door latch may not be in the correct location, possibly preventing the door from latching properly.
If the right rear passenger door opens unexpectedly, it can increase the risk of injury.
Chrysler will notify owners, and dealers will repair the right rear door latch reinforcement, free of charge. The recall begin December 6, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UB6.
Campaign 18V786000 on NHTSA.gov
Structure, frame and membersSep 28, 2018
Chrysler (FCA US LLC) is recalling certain 2018-2019 Jeep Wrangler vehicles. The front track bar brackets may be improperly welded, which can cause the bracket to separate from the frame, reducing steering capability.
An unexpected reduction in steering ability, can increase the risk of a crash.
Chrysler will notify owners, and dealers will inspect and repair the track bar bracket welds, as necessary, free of charge. The recall is expected to begin November 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UA5.
Campaign 18V675000 on NHTSA.gov
Electrical system, wiring, front underhoodAug 9, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.
A vehicle stall can increase the risk of a crash.
Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.
Campaign 18V524000 on NHTSA.gov
SteeringMay 25, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The intermediate steering shaft may not have been properly welded causing a split where the external spline is formed.
If the weld seam splits, the steering wheel may lose center positioning causing a loss of steering responsiveness and increasing the risk of a crash.
Chrysler will notify owners, and dealers will inspect and, as necessary, replace the intermediate steering shaft, free of charge. The recall began June 21, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U48.
Campaign 18V343000 on NHTSA.gov
Electrical system, wiringMay 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Campaign 18V332000 on NHTSA.gov
Power train, automatic transmissionMay 1, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Dodge Charger, Durango and Challenger, Jeep Grand Cherokee and Wrangler, Chrysler 300, and RAM 1500 vehicles. An incorrect transmission park lock rod may have been installed in the transmission.
If the incorrect park lock rod is installed, the transmission may not shift into 'PARK' and keep the vehicle from moving, increasing the risk of unintended vehicle movement and the risk of a crash.
Chrysler will notify owners, and dealers will install the correct park lock rod, free of charge. The recall began June 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U43.
Campaign 18V280000 on NHTSA.gov
Structure, frame and membersApr 12, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The rear under body ladder rail may corrode, possibly reducing the strength of the rear floor pan and causing the left rear seat mount to become loose.
If the floor pan strength is reduced and/or the rear seat mount becomes loose, the rear seat may detach in a crash, increasing the risk of injury.
Chrysler will notify owners, and dealers will inspect and, as necessary, coat the interior and exterior of the driver's side rear underbody ladder rail with three-part rust protection. The recall began September 11, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U27.
Campaign 18V231000 on NHTSA.gov
Representative owner complaints: service brakes
67 reports, newest first. Show all
Service brakes, Sep 2, 2026
2018 Jeep Wrangler rubber brake lines collapsing internally, trapping hydraulic fluid pressure, and causing front brakes to overheat/lock up. Happened last year on my driver's side. It completely locked up my caliper. Ended up replacing Front Driver Hose & Caliper. And both Front Rotors and Brake Pads. Now its currently happening to my passenger side. This time its actually causing a burning smell. Last year it did not it was just grinding. Been for a few months. At first I though it was my aux battery that was dead and was causing the smell. But got that looked at and didnt even have a ln aux battery. Didnt notice the smell for a few months. But now in extreme heat and worsen driving conditions it has came back. Was told my hose is collapsing. So now I have to replace rotors and brake pads again. And new hose and caliper on my passenger side
Electrical system, Service brakes, Aug 19, 2026
On Monday, XXX, my 2018 Jeep Wrangler JKU had several errors displayed on the dashboard: ABS, Brake, and Traction Control failures. I took my vehicle to an auto repair shop and they diagnosed it as a faulty ABS Module. This part is on back-order as per discussion with local Jeep dealers in [XXX]. Stellantis confirms that this part is not available as it has been deemed a systematic failure. There is currently no solution from Stellantis which is causing safety concerns and increased risk of operating my Jeep Wrangler. The error code is C2200: ANTI-LOCK BRAKE MODULE INTERNAL - STORED. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Service brakes, Aug 18, 2026
I took it in for the Maine state inspection and it won't pass because the rotors have delaminated, the caliper is starting to shift up, and the brake hoses are going bad already. The service tech says this is a known issue with these vehicles. Unacceptable for a vehicle with 42k miles.
Service brakes, Aug 15, 2026
2018 Jeep Wangler JK experienced a brake failure due to a rusted collapsed right front brake line. Vehicle is one owner with 29,855 miles at time of repair on 08/05/26. Repaired by independent service center. Garage kept for the first 6 of 8 years of ownership, never operated off road, and no accidents. Parked in a covered car port for last two years when not in use. This is a well maintained, daily driver vehicle driven by a 79 year old male.
Service brakes, Aug 8, 2026
The vehicle experienced repeated braking system failures that caused the front brakes to lock up while driving, overheat, and begin smoking. The front brake calipers, rotors, and pads were replaced multiple times,not lasting more than 3weeks before failing again. the problem continued to occur. The brake booster brake line and brake fluid were also replaced while attempting to diagnose the problem. Warning lights/messages appeared, including the ABS/traction control warning and “Service Electronic Stability Control.” The vehicle would also randomly turn off at stop lights and refuse to turn back on. An independent mechanic ultimately diagnosed a failure of the ABS control module. Showing a code “c2200” The vehicle is currently at the repair facility and is available for inspection. This failure created a serious safety risk because the brakes could engage/lock unexpectedly while the vehicle was being driven and the braking system became severely overheated and damaged multiple times. The vehicle is currently considered unsafe to drive unless I redo the whole braking system again and unplug the ABS module. I was informed that the required replacement ABS module is on national backorder with no reliable availability date and reliable refurbishes are also unable to do the repairs now. . I was also informed that obtaining a new replacement module may take an extended period of time. Because this is a safety-critical braking component, I am concerned that other vehicles with the same failure could experience unexpected brake malfunction or loss of safe braking control
Service brakes, Aug 6, 2026
3 out of the 4 calipers have failed.
Service brakes, Jul 26, 2026
The abs module has failed and i have no traction control or abs function all the lights are on the dash a common issue with the jk jeep wrangler platform
Service brakes, Hydraulic, Jul 6, 2026
The contact owns a 2018 Jeep Wrangler JK. The contact stated that the ABS warning light was illuminated. While driving, the vehicle experienced a loss of traction, a pulsating or pumping sensation in the brake pedal, and skidded easily upon heavy brake application. The contact associated the failure with NHTSA Campaign Number: 24V896000 (Service Brakes, Hydraulic); however, Jeep models were not included in the recall parameters. The vehicle was taken to a dealer, where it was diagnosed with electronic control unit (ECU), electronic stability control (ESC), traction control, and ABS failures. The vehicle was not repaired because the parts were on backorder. The manufacturer was notified of the failure. The failure mileage was 42,000.
Steering, Service brakes, Hydraulic, Power train, Jun 23, 2026
The contact owns a 2018 Jeep Wrangler. The contact stated that while driving 20 miles away after an hour, the vehicle lost power steering and power braking functionality, and the transmission unexpectedly downshifted to a lower gear. The vehicle was turned off. The check engine warning light was illuminated. The vehicle was towed to the residence. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 91,300.
Other or unspecified, Service brakes, Jun 4, 2026
I own a 2018 Jeep Wrangler that my 19 year old son drives for college. While driving, the vehicle jerked and became sluggish. There were no warning lights illuminated. I became aware that the front brake rotors had overheated again. I had the front right brake caliber and brake line changed back in 2024 and the issue has recurred this year. I had a local mechanic change the front brake pads and rotors for both front tires and caliber to right front side only in April/2026 and the issue has started again today. The vehicle was taken back to local mechanic to be diagnosed again. He stated that the brake fluid was unable to properly bleed through the brake line restricting air to fully purge from the hydraulic system, which can result in incomplete bleeding, reduced braking performance, uneven pad wear, brake drag, or brake fade and is part of the reason for burning smell near right front tire. He added that car isn’t safe to drive in this condition due to safety concerns of accidents due to inability to properly brake or even a fire. Vehicle hasn’t been repaired due to cost and I will attempt to contact manufacturer. The initial mileage reading when this issue occurred in 2024 was 90,000 miles. The mileage as of this complaint is 112,392.
Service brakes, Hydraulic, Feb 3, 2026
The contact owns a 2018 Jeep Wrangler. The contact stated that when the vehicle was started, the ABS and brake warning lights were illuminated. The contact stated that while depressing the brake pedal, the warning lights illuminated the brake pedal was soft. The contact stated that additional pressure was needed to depress the brake pedal to stop the vehicle. Additionally, the check engine warning light was intermittently illuminated. The vehicle was taken to a local dealer, where it was diagnosed and determined that the ABS module had failed and needed to be replaced; however, the part to repair the vehicle was on a national backorder. The vehicle was not repaired. The manufacturer was informed of the failure, and a complaint was filed. The failure mileage was approximately 69,000.
Service brakes, Fuel/propulsion system, Jan 18, 2026, crash
My wife and I were at a stop light behind a box truck in our 2018 Jeep Wrangler, about 15 feet between us. I had slowed to stop and had my foot on the brake. All of the sudden the Jeep reved up (idle increase), did not see the tachometer, and with my foot on the brake accelerated into the box truck in front of us. When it started to accelerate, I pushed the brake peddle to the floor to stop the Jeep but it did not do a thing. I see 2 problems her: 1. The acceleration when stopped 2. The brake did not hold. There were no injuries or damage to the box truck. We were able to drive the Jeep about 20 miles to the dealer we bought at. It is ow being worked on in the body shop. The Jeep dealer technicians did a computer check on any codes that were activated, but unfortunately all after the fact.
Service brakes, Jan 7, 2026
The front right brake caliper on my 2018 Jeep Wrangler was installed upside down from the factory, with the bleeder screw located at the bottom of the caliper instead of the top. The vehicle has been serviced exclusively at authorized Jeep dealerships since new, with no prior front brake work, confirming this was a factory assembly defect and not the result of repair or modification. Because the bleeder screw is positioned at the bottom, air cannot be fully purged from the hydraulic system, which can result in incomplete bleeding, reduced braking performance, uneven pad wear, brake drag, or brake fade. This condition compromises the ability to properly service the braking system and may negatively affect braking effectiveness, creating a potential safety hazard, especially during emergency braking. The defect was discovered during routine inspection when brake performance and wear were evaluated (12-11-25). Photographs and dealership service records are available documenting the inverted caliper and confirming no prior disassembly.
Service brakes, Oct 13, 2025
The ABS module has failed on the vehicle. Attempts to repair it have been unsuccessful due to the part being back ordered for years.
Electrical system, Vehicle speed control, Service brakes, Oct 3, 2025
ABS module has failed and has shut off the cruse control system. The O.E. module is on national back order with no idea of it availability. The unit is still in the vehicle. Non-A.B.S. brakes work. How ever the traction control system is shut off as well as the cruse control system posing a greater risk to all. Search on several internet sites confirms that this issue has been noted to the manufacture with no resolution. Owners are left to find their own part and none are available.
Steering, Service brakes, Sep 4, 2025
The primary component that failed is the brake caliper, which caused a dragging brake, overheating, and visible smoke after a brake pad replacement. This is a defect in a critical safety system, not routine wear and tear. The caliper failure, combined with rapid deterioration of the pads within only seven months of purchase, makes clear that the Jeep was sold to me with preexisting and undisclosed defects. The defective caliper and removed parts remain available for inspection. My safety and the safety of others were directly at risk. A dragging brake drastically reduces stopping ability, can cause sudden brake failure, and creates a fire hazard when smoke and heat build up. These risks make the vehicle unsafe for road use. In addition, there is a well-documented steering defect known as the “death wobble.” Some sources classify this under a recall, while others describe it as covered only by an extended warranty. This inconsistency has prevented me from obtaining clear assistance despite the serious safety implications. The issue has been reproduced and confirmed by a certified Jeep dealership. I have service records, dealer inspection notes, and photos documenting the condition, including metal-on-metal wear, dragging brake, and resulting smoke. The vehicle has been inspected by dealership technicians and is also under review with FCA, who have assigned a claim number. When I initially sought assistance, I was told the failures were “wear and tear.” That is inaccurate, as no reasonable consumer could cause this level of brake and steering deterioration in such a short period. I have been forced to pay out-of-pocket for defects clearly present at the time of sale, even though Carvana, SilverRock, and FCA denied responsibility. Under the Magnuson-Moss Warranty Act, consumers are protected when vehicles are sold with hidden defects, regardless of warranty status. This Jeep was sold in unsafe condition. The caliper failure and death wobble are preexisting hazards
Service brakes, Hydraulic, Aug 22, 2025
The contact's son owns a 2018 Jeep Wrangler. The contact stated while driving 25 MPH and pulling into a parking lot, the vehicle felt like one of the front tires was not rotating. The contact was able to pull into a parking space. Upon inspecting the vehicle, the contact noticed that the driver's side front tire was not rotating. The contact and a bystander noticed that the driver's side front tire was not rotating because the front brake caliper was protruding through the rim. The contact's husband arrived at the scene, removed the tire, and zip tied the caliper to the frame, and the vehicle was driven to the residence. The vehicle was taken to the dealer, where the brake pads, rotors, and the calipers were replaced; however, the failure persisted. The vehicle was towed to the dealer, where it was diagnosed that the front brake lines had rusted internally, causing the brake lines to collapse. The dealer informed the contact that the failure prevented the brake fluid to reach the brakes, which remained close to the rotors and had burned out. The dealer determined that the front driver's side brake line, rotors, calipers, and the brake pads needed to be replaced. The vehicle was not repaired due to the cost. The manufacturer was not notified of the failure. The failure mileage was approximately 90,100.
Service brakes, Jul 30, 2025
My ABS module has failed. Should be a simple fix however Jeep does not have this part available to be purchased. After doing a lot of research into this part it is a Mopar only part and there are thousands of people trying to find this part. This part is a vital part to the ABS system and is causing a lot of people to have to drive without it. Something needs to be done to ensure the safety of everyone that is going through this issue.
Steering, Suspension, Service brakes, Jul 18, 2025
On [XXX] while driving my 2018 Jeep Wrangler Unlimited Sport (VIN: [XXX] ), the braking system failed without warning while I was approaching a stop sign on a residential road. I pressed the brake pedal and felt extreme resistance and grinding, followed by a near-total lack of braking power. I was forced to abruptly swerve into an open driveway to avoid a collision. This sudden malfunction put my life and the safety of others at serious risk, especially had it occurred on a highway or near pedestrian traffic. The affected component appears to be part of the braking system—likely the master cylinder, brake booster, or brake line integrity—but a full diagnosis is pending inspection. There were no warning lights or messages displayed on the dashboard at any time prior to or during the failure. The vehicle gave no indication that a malfunction was imminent. Immediately after the incident, I parked the vehicle and did not attempt to drive it again. As of now, the issue has not yet been formally confirmed by a dealer, but I am in the process of getting it inspected by a certified independent mechanic, and I am willing to make the vehicle and its components available for inspection upon request. I also plan to provide documentation once the evaluation is complete. I only recently purchased this Jeep from Carvana a few months ago, and it is extremely concerning that such a critical failure could occur so soon. The vehicle has two completed recalls related to steering and rear windows, but none that address braking—making this unexpected failure even more alarming. I believe this could indicate a larger pattern or potential defect that has not yet been officially acknowledged or addressed. This event was dangerous and could have resulted in a serious accident. I am requesting that this complaint be formally investigated, and I am open to cooperating fully with NHTSA, Chrysler, or any affiliated parties in reviewing the failure and addressing issue. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Service brakes, Hydraulic, Jun 11, 2025
The contact owns a 2018 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed, but the vehicle slid before coming to a stop. The contact stated that the traction control warning light was illuminated. The vehicle was taken to an independent mechanic, who diagnosed the vehicle with ABS failure, and determined that the braking system needed to be replaced. The vehicle was taken to another independent mechanic, who related the failure to the ABS module. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 121,000.
Power train, Electrical system, Service brakes, May 20, 2025
First it was my clutch blowing up including the transmission from underneath me while I drove down a hwy. Then it was a month later before I got it back. (I'm single, and it's my only vehicle). Once I got my jeep back the start/stop button stopped working. I had to lock/unlock with the key fob for it to start. Even with both fobs in the jeep. Now every code, 101 to be exact) is being thrown out of nowhere. Every light goes off, the wipers start going off, the sway bar and traction control disconnects while I'm driving along with the steering wheel locking up while I'm driving down the hwy. The brakes are pulling very badky to the left and /or right. The entire thing is absolutely a death trap. I can't believe this was passed by someone who has the customers best interest for safety. I'd like to know if any of this is recalled because it's been every jeep from 2018-2021 that have this issues. Also 5th gear now vibrats pretty bad.
Service brakes, Hydraulic, Air bags, May 14, 2025
The contact owns a 2018 Jeep Wrangler. The contact stated while driving at an undisclosed speed, the ABS warning light illuminated. The vehicle was taken to an independent mechanic where it was diagnosed with a failed clock spring. The contact was informed that the clock spring needed to be replaced. The vehicle was not repaired. In addition, the contact stated that several of the steering wheel safety features were inoperable due to the failure. The dealer was made aware of the failure. The contact was informed that a diagnostic test was needed to determine the cause of the failure. The manufacturer was not made aware of the failure. The failure mileage was 35,000.
Steering, Electrical system, Service brakes, May 6, 2025
ABS malfunction. Power steering and brakes go in and out of operation due to a communication error. All lights come on dash, engine light stays on. Occurs mainly when vehicle is hot during summer or above 65mph highway driving. Safety concern as vehicle power steering is unpredictable during this time. The Drive shaft locks in park and requires manual override when lights are on, but then without intervention, all the lights go away except the engine light and it runs fine. ABS modules are on back order with no ETA because this is a recurring problem for many. Once new abs module is put it, problem can be confirmed and more details can be given by auto repair services.
Power train, Electrical system, Service brakes, Mar 11, 2025
While driving the transmission and clutch system blew up. And I mean that in the literale sense. Sparks and a big flash. Unfortunately, I was an hour away from where I live. This caused me to have to find a way home and find a tow company that would be able to pick up my jeep on the side of the highway, tow it an hour to me. I couldn't afford that, so it was taken to the Chrysler dealership there and it was there for a month before they could work on it due to the parts having to be ordered and shipped in. Once the entire clutch system and transmission fully replaced I have to find a way to go back and pick it up. It was after hours when I finally got to it. That's when the mechanic that worked on it researched and found the recall for the transmission and clutch system because they would blow up. Just as mine did. But the next set of problems started as soon as I picked my jeep up. Pulls to the right when braking, push start won't start saying the fobs are not detected while I'm holding them in my hands. All lights on cluster go off randomly, the steering wheel locks up while I'm driving causing more danger. The traction control, sway bar will go off and on as well as the push start will not turn off. I did manage to take a short clip of this happening while I'm driving.
Service brakes, Mar 10, 2025
The brake line and caliper. The safety of myself and my children were at risk. Yes it has been confirmed as a problem from a dealer mechanic. It has not been inspected by police or others listed. There were no warnings or symptoms. It started smoking and the car shook while driving. This has now happened twice.