2018 Jeep Wrangler
Problems, recalls and owner-reported issues
Steering is the leading concern among 1,822 owner complaints filed for this model year. This is the highest complaint count among 26 Wrangler model years with reports.
Of the 2018 reports, 22 involved a crash and 25 involved a fire. 13 people were injured.
What owners report most often
Recalls and investigations
Back over prevention, sensing system, cameraSep 12, 2024
Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."
A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.
Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 77B.
Campaign 24V676000 on NHTSA.gov
Electrical system, instrument cluster/panelSep 5, 2024
Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."
An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.
Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 30B.
Campaign 24V652000 on NHTSA.gov
Power train, clutch assemblyFeb 23, 2023
Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Dealers will replace the clutch assembly and update the software, free of charge. Owner notification letters were mailed from November 16, 2023 through July 25, 2024. Owners may contact (FCA US, LLC) customer service at 1-800-853-1403. FCA US LLC's number for this recall is 19A. This recall expands and replaces previous recall 21V-028. Vehicles previously repaired under recall 21V-028 will need to have the new remedy completed.
Campaign 23V116000 on NHTSA.gov
Power train, clutch assemblyJan 28, 2021
Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
FCA US LLC will notify owners, and dealers will add software to reduce engine torque capability when clutch assembly temperatures rise to a level that may damage the inner pressure plate, free of charge." FCA has ordered a stop sale for the affected vehicles as of February 25, 2021. Owner notification letters were mailed on March 4, 2021.
Campaign 21V028000 on NHTSA.gov
Power train, clutch assemblyMar 3, 2020
Chrysler (FCA US LLC) is recalling certain 2018-2020 Jeep Wrangler and 2020 Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
The overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Chrysler will notify owners, and dealers will reroute a wire harness and inspect the clutch system, and replace components as needed. The recall began April 30, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W12.
Campaign 20V124000 on NHTSA.gov
Seat belts, front, anchorageSep 26, 2019
Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.
A separated or severed seat belt buckle strap will result in an inoperable seat belt, increasing the risk of injury in the event of a crash.
FCA US will notify owners, and dealers will replace the driver's seat belt buckle, free of charge. Interim notices informing owners of the safety risk were mailed November 19, 2019. Owners will received a second letter and the recall began March 26, 2020. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is VA6.
Campaign 19V680000 on NHTSA.gov
EquipmentApr 23, 2019
Erwin Hymer Group USA LP dba American Fastbacks (EHGUSA-AF) is recalling certain 2018 Jeep Wrangler vehicles sold with a roof top tent installed. The top cover of the roof top tent may crack or break, possibly resulting in the cover detaching from the vehicle while moving.
If the roof top tent cover detaches from the vehicle while moving, it can create a road hazard, increasing the risk of a crash.
The remedy for this recall is still under development. The recall began May 9, 2019. Owners may contact American Fastbacks customer service at 1-844-533-7997 extension 301. Note: Vehicles in this recall are also included in recall 19V-190.
Campaign 19V320000 on NHTSA.gov
Latches/locks/linkages, doors, latchNov 8, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler four-door vehicles. The right rear passenger door latch may not be in the correct location, possibly preventing the door from latching properly.
If the right rear passenger door opens unexpectedly, it can increase the risk of injury.
Chrysler will notify owners, and dealers will repair the right rear door latch reinforcement, free of charge. The recall begin December 6, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UB6.
Campaign 18V786000 on NHTSA.gov
Structure, frame and membersSep 28, 2018
Chrysler (FCA US LLC) is recalling certain 2018-2019 Jeep Wrangler vehicles. The front track bar brackets may be improperly welded, which can cause the bracket to separate from the frame, reducing steering capability.
An unexpected reduction in steering ability, can increase the risk of a crash.
Chrysler will notify owners, and dealers will inspect and repair the track bar bracket welds, as necessary, free of charge. The recall is expected to begin November 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UA5.
Campaign 18V675000 on NHTSA.gov
Electrical system, wiring, front underhoodAug 9, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.
A vehicle stall can increase the risk of a crash.
Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.
Campaign 18V524000 on NHTSA.gov
SteeringMay 25, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The intermediate steering shaft may not have been properly welded causing a split where the external spline is formed.
If the weld seam splits, the steering wheel may lose center positioning causing a loss of steering responsiveness and increasing the risk of a crash.
Chrysler will notify owners, and dealers will inspect and, as necessary, replace the intermediate steering shaft, free of charge. The recall began June 21, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U48.
Campaign 18V343000 on NHTSA.gov
Electrical system, wiringMay 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Campaign 18V332000 on NHTSA.gov
Power train, automatic transmissionMay 1, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Dodge Charger, Durango and Challenger, Jeep Grand Cherokee and Wrangler, Chrysler 300, and RAM 1500 vehicles. An incorrect transmission park lock rod may have been installed in the transmission.
If the incorrect park lock rod is installed, the transmission may not shift into 'PARK' and keep the vehicle from moving, increasing the risk of unintended vehicle movement and the risk of a crash.
Chrysler will notify owners, and dealers will install the correct park lock rod, free of charge. The recall began June 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U43.
Campaign 18V280000 on NHTSA.gov
Structure, frame and membersApr 12, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The rear under body ladder rail may corrode, possibly reducing the strength of the rear floor pan and causing the left rear seat mount to become loose.
If the floor pan strength is reduced and/or the rear seat mount becomes loose, the rear seat may detach in a crash, increasing the risk of injury.
Chrysler will notify owners, and dealers will inspect and, as necessary, coat the interior and exterior of the driver's side rear underbody ladder rail with three-part rust protection. The recall began September 11, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U27.
Campaign 18V231000 on NHTSA.gov
Representative owner complaints
1,822 reports, newest first.
Service brakes, Aug 8, 2026
The vehicle experienced repeated braking system failures that caused the front brakes to lock up while driving, overheat, and begin smoking. The front brake calipers, rotors, and pads were replaced multiple times,not lasting more than 3weeks before failing again. the problem continued to occur. The brake booster brake line and brake fluid were also replaced while attempting to diagnose the problem. Warning lights/messages appeared, including the ABS/traction control warning and “Service Electronic Stability Control.” The vehicle would also randomly turn off at stop lights and refuse to turn back on. An independent mechanic ultimately diagnosed a failure of the ABS control module. Showing a code “c2200” The vehicle is currently at the repair facility and is available for inspection. This failure created a serious safety risk because the brakes could engage/lock unexpectedly while the vehicle was being driven and the braking system became severely overheated and damaged multiple times. The vehicle is currently considered unsafe to drive unless I redo the whole braking system again and unplug the ABS module. I was informed that the required replacement ABS module is on national backorder with no reliable availability date and reliable refurbishes are also unable to do the repairs now. . I was also informed that obtaining a new replacement module may take an extended period of time. Because this is a safety-critical braking component, I am concerned that other vehicles with the same failure could experience unexpected brake malfunction or loss of safe braking control
Electrical system, Aug 7, 2026
I have a 2018 Jeep Wrangler JL. Both digital and analog dash gauges have stopped working. I am unable to read odometer, speedometer, gas level, RPM, temperature gauge, etc. This poses a significant risk to my safety while driving.
Service brakes, Aug 6, 2026
3 out of the 4 calipers have failed.
Service brakes, Jul 26, 2026
The abs module has failed and i have no traction control or abs function all the lights are on the dash a common issue with the jk jeep wrangler platform
Structure, Jul 15, 2026
1 - rear door opened while driving, door was checked closed before driving on 7/14/26, it is available for inspection 2 - safety for others were at risk, as some of contents exited vehicle on road 3 - have an appointment on 7/21/26 with original cr dealer 4 - waiting on car dealer to inspect it 5 - no warning lights or messages, first apppeared on 7/14/26
Electrical system, Jul 13, 2026
The contact owns a 2018 Jeep Wrangler. The contact stated that upon starting the vehicle the instrument panel would not illuminate, due to the failure, no warning lights were illuminated. The vehicle was taken to a local dealer where the vehicle was diagnosed and the contact was advised that the instrument panel was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and offered no assistance as the vin was not allocated to a recall. The failure mileage was 50,000.
Electrical system, Jul 13, 2026
The instrument cluster display in my 2018 Jeep Wrangler Sahara has failed. The display is either blank or nonfunctional, preventing me from viewing critical vehicle information and safety warnings while driving. This failure affects my ability to monitor engine temperature, fuel tank capacity, warning messages, fault indicators, and other important vehicle operating information. As a result, I may not be alerted to potentially dangerous conditions such as engine overheating, low oil pressure, charging system failures, or other safety-related issues. I am aware that Jeep has issued recalls involving instrument cluster defects on certain Wrangler vehicles, but my VIN is not included in the recall. The symptoms of my vehicle appear similar to those reported in recalled vehicles. Because the instrument cluster is a primary safety component used to communicate vehicle warnings and operating conditions to the driver, I believe this defect presents a safety risk. I am submitting this complaint so the issue can be investigated and to determine whether additional vehicles should be covered.
Engine, Fuel/propulsion system, Jul 13, 2026
I purchased this 2018 Jeep Wrangler JK Unlimited on July 19, 2025. Since purchasing the vehicle, I have experienced repeated mechanical failures that have required multiple repairs. The most serious issue involves the engine overheating at highway speeds without any visible coolant leak or clearly identifiable cause.Despite seeking professional diagnosis, the source of the overheating could not be determined. Shortly afterward, the vehicle developed a P0302 (Cylinder 2 Misfire), raising concerns about possible internal engine damage caused by the overheating.I believe this presents a significant safety hazard. An engine that overheats unexpectedly while driving at highway speeds can lose power or fail without warning, creating a dangerous situation for the driver and surrounding traffic. The vehicle has become unreliable and unsafe to operate because I cannot predict when it may overheat or experience another engine failure.As someone who often drives alone, I no longer feel safe taking this vehicle on long trips. I am concerned that the vehicle could leave me stranded on a highway or in a remote location without warning, placing my personal safety at risk. A vehicle should provide dependable transportation, not expose its occupants to the possibility of sudden mechanical failure.This vehicle has spent more time in repair facilities than on the road. I have incurred thousands of dollars in repair expenses, and I am now being asked to pay for an engine teardown simply to determine the cause of the failure before any warranty consideration can be made. Despite multiple repair attempts, the underlying cause of the overheating and engine problems has not been resolved.I am submitting this complaint because I believe the repeated overheating, unexplained engine malfunction, and resulting cylinder misfire may indicate a safety-related defect that warrants investigation. I request that the review to determine whether similar failure whether a broader safety issu
Service brakes, Hydraulic, Jul 6, 2026
The contact owns a 2018 Jeep Wrangler JK. The contact stated that the ABS warning light was illuminated. While driving, the vehicle experienced a loss of traction, a pulsating or pumping sensation in the brake pedal, and skidded easily upon heavy brake application. The contact associated the failure with NHTSA Campaign Number: 24V896000 (Service Brakes, Hydraulic); however, Jeep models were not included in the recall parameters. The vehicle was taken to a dealer, where it was diagnosed with electronic control unit (ECU), electronic stability control (ESC), traction control, and ABS failures. The vehicle was not repaired because the parts were on backorder. The manufacturer was notified of the failure. The failure mileage was 42,000.
Steering, Service brakes, Hydraulic, Power train, Jun 23, 2026
The contact owns a 2018 Jeep Wrangler. The contact stated that while driving 20 miles away after an hour, the vehicle lost power steering and power braking functionality, and the transmission unexpectedly downshifted to a lower gear. The vehicle was turned off. The check engine warning light was illuminated. The vehicle was towed to the residence. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 91,300.
Electrical system, Other or unspecified, Engine, Jun 22, 2026, fire
What component or system failed or malfunctioned, and is it available for inspection upon request? Jeep started on fire and is still at a tow yard in Belchertown, MA How was your safety or the safety of others put at risk? The Jeep started on fire while I was driving. I pulled over as the engine was smoking and then it burst into flames while I was still inside. Has the problem been reproduced or confirmed by a dealer or independent service center? Not that I know of. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Yes, we gave permission for our insurance agency and Jeep to inspect the burned out vehicle. Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? While I was driving, the engine temp and coolant warning lights shot way up and then the engine began to smoke. I pulled over and before I could exit the vehicle, fire was coming into the cab through the air vents.
Other or unspecified, Jun 22, 2026
EGR pre conditions to pass CA state smog emissions test will not clear. Have changed entire EGR system and have drive the recommended Chrysler Drive cycle for my car with hundreds of miles on it since replacing battery with no luck. All other system checks clear.
Steering, Suspension, Jun 10, 2026
Any time I am over the speed of about 55 mph, and hit any type of bump, the steering wheel starts to shake violently. I have to slow down to about 40 mph to make it stop. I almost got rearended by an 18-wheeler yesterday on the interstate.
Engine and engine cooling, Power train, Jun 10, 2026
The contact owns a 2018 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the steering wheel seized and the vehicle failed to accelerate. The electronic parking brake, check engine, and several other unknown warning lights were illuminated. The contact shifted to park (P) and then drive (D) and was able to continue driving. The vehicle was taken to the dealer, who was unable to duplicate the failure. The vehicle was taken to an independent mechanic, who determined that coolant had leaked into the computer and damaged the battery pack control module. The mechanic related the failure to Customer Satisfaction Program: Y40 (Control Module Software Updates); however, the VIN was not included. The vehicle was then towed to an unknown dealer; however, the vehicle was not yet diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 100,000.
Other or unspecified, Service brakes, Jun 4, 2026
I own a 2018 Jeep Wrangler that my 19 year old son drives for college. While driving, the vehicle jerked and became sluggish. There were no warning lights illuminated. I became aware that the front brake rotors had overheated again. I had the front right brake caliber and brake line changed back in 2024 and the issue has recurred this year. I had a local mechanic change the front brake pads and rotors for both front tires and caliber to right front side only in April/2026 and the issue has started again today. The vehicle was taken back to local mechanic to be diagnosed again. He stated that the brake fluid was unable to properly bleed through the brake line restricting air to fully purge from the hydraulic system, which can result in incomplete bleeding, reduced braking performance, uneven pad wear, brake drag, or brake fade and is part of the reason for burning smell near right front tire. He added that car isn’t safe to drive in this condition due to safety concerns of accidents due to inability to properly brake or even a fire. Vehicle hasn’t been repaired due to cost and I will attempt to contact manufacturer. The initial mileage reading when this issue occurred in 2024 was 90,000 miles. The mileage as of this complaint is 112,392.
Electrical system, May 30, 2026
My electronic instrument panel went completely out. I could not tell my speed, amount of gas, mileage, or anything else. This happened suddenly and without any warning.
Power train, May 28, 2026
I had the clutch plate recall done on my 2018 jeep wrangler unlimited 3.6 in January 2024. The first 8 months my dash lite up warning me my clutch is overheating and to reduce clutch use. This happens every time im on traffic or reversing around obstacles going up hill. The dash also lite up saying clutch performance is limited reduce clutch use. This is still happening after the recall was completed and its May 2026 currently trying to get it fixed. I have pictures of the dash lighting up with 3 different warning about the clutch plate
Engine, May 22, 2026, crash
Was stopping at red light. Got to about 5mph when Jeep accelerated to about 35mph. I was standing on the breaks but the Jeep kept accelerating until impact struck the car in front me which was stopped. I have video.
Electrical system, May 20, 2026
Defect in the instrument panel cluster (IPC) that can cause it to go blank or fail entirely. Screen is completely blank which makes it impossible to monitor or see any warnings for vehicle with it being an electrical dash. There is a safety recall on 2018-2024 Wranglers, but for some reason my VIN does not populate on the recall when I have a 2018 Wrangler. This has caused me not to be monitor oil life, fuel, and see check engine notifications. NHTSA Recall Number: 24V‑652 for year model 2018–2024 Wranglers (and 2020–2024 Gladiators)
Steering, Electrical system, Engine, May 18, 2026
I bought this vehicle used in 2022 from CarMax. According to Jeep (Stellantis) Co. multiple recalls were fixed by the previous owner, but the patch available for 2018 Jeep Wranglers was not done. In 2024 my iphone and Mac laptop were hacked and shortly after I began having problems with my 2018 Jeep Wrangler. My alarm system started going off while I was in my home without touching or being near the FOB. When I used my FOB to unlock the doors, they would lock back before I could open the door. I was unable to use the push button start for a few minutes up to 15 minutes and in 2025 I was unable to use the push button at all on most days. I had to research a work around to be able to start my Jeep and even after that depending on the day, it takes several seconds to minutes to start it this way. On 2 different occasions as I was driving, I had no control over my steering for approx. 10 seconds. I held on to the wheel and slowed down. The control returned and I was able to drive home. I researched and found out that 2014-2018 had reports of hacking and the hacker taking control of the vehicle in multiple ways including steering, brakes, alarm system, and hacking FOB. My radio has been turned off and the stations changed. One of my FOBs was tampered with, including switching the lock and unlock button's capability, panic button was disabled, and now the FOB does not work at all. There is a loud grinding noise behind my glove box that can be heard at different times including when Jeep is turned off. Loud noises that sound like a rock hitting the window happen randomly to my front windshield, driver and passenger windows happens multiple times while I am driving and when vehicle is turned off. I took Jeep to a trusted mechanic and was told there was no way to tell and it would be better to just sell it. After I moved, I didn't experience these problems for a while, but am experiencing them again. I am concerned for my safety and anyone who may be a passenger in my Jeep.
Engine, May 17, 2026
Engine - The vehicle is available but the engine was replaced. I was able to get home however there was a potential for significant engine failure. Yes it was inspected by an independent service center. Yes it was inspected by an independent service center. A check engine light came on. Upon further inspection it was a Cylinder 6 misfire P0306. When the engine was inspected further by a mechanic it was determined that the cylinder wall was damaged and that coolant had entered the cylinder. Due to the extent of the engine damage the engine needed to be replaced.
Engine, May 16, 2026
Oil cooler failure at 7 years and 90000 miles. This is a known engineering issue due to a plastic housing that is resolved by upgrading the oil cooler housing to aluminum instead of plastic. It’s a $1000 repair. Because this is an engineering issue the consumer should not have to pay the entire cost of the repair. This is a SAFETY AND ENVIRONMENTAL HAZARD DUE TO THE LEAKAGE OF OIL CAUSED BY THIS FAILURE. It should definitely be deemed a recall and fixed at the expense of the manufacturer!
Power train, May 16, 2026
While driving my engine light comes on and I lose power like it won’t take gear I can switch to manual and it’s fine engine light pulls a code for oil pressure sensor but I’ve done paid for that to be fixed and it still doing the same as above but the engine light will go off after cutting the jeep off and stays off for a few days then out of nowhere while driving it comes back on and the process starts all over
Electrical system, May 11, 2026
The instrument cluster went black when I was driving. This prevents the driver from seeing warning lights, digital speedometer, the fuel gauge and the odometer. The car was examined by my private mechanic, and he stated he could not fix it. He advised me to go to the Jeep dealership. The car was then examined by the dealership, and they stated it would need a new instrument cluster at a cost of $1600, and I was charged $250 for the diagnostic. I then researched the issue and learned that Jeep has issued 2 recalls for this exact problem which included the make, model and year of my unit. The recall dates were September 2024 and April 2026. I called Jeep's help center and they stated my particular vehicle is not eligible for the recall because of where it was made. I feel this is not a valid reason and they should honor the recall for my vehicle.
Steering, Power train, Electrical system, May 4, 2026
One day out of the blue, my Jeep Wrangler received a "Service Shifter" error code. The error code threw about 40 other codes at the same time. Loss of power steering, loss of abs, engine kept revving on its own, windshield wipers turned on. While in park it felt as if it was trying to shift itself into other gears. Loss of steering while driving as well as the engine revving up and down while on the interstate. Every warning light came on and stayed on. I can let it sit for awhile and it'll drive fine for a little while until it does it all again and again. I have not taken it to a dealership yet due to all the threads on being charged $2000 and it not get fixed.