2018 Jeep Wrangler
Problems, recalls and owner-reported issues
Steering is the leading concern among 1,822 owner complaints filed for this model year. This is the highest complaint count among 26 Wrangler model years with reports.
Of the 2018 reports, 22 involved a crash and 25 involved a fire. 13 people were injured.
What owners report most often
Recalls and investigations
Back over prevention, sensing system, cameraSep 12, 2024
Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."
A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.
Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 77B.
Campaign 24V676000 on NHTSA.gov
Electrical system, instrument cluster/panelSep 5, 2024
Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."
An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.
Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 30B.
Campaign 24V652000 on NHTSA.gov
Power train, clutch assemblyFeb 23, 2023
Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Dealers will replace the clutch assembly and update the software, free of charge. Owner notification letters were mailed from November 16, 2023 through July 25, 2024. Owners may contact (FCA US, LLC) customer service at 1-800-853-1403. FCA US LLC's number for this recall is 19A. This recall expands and replaces previous recall 21V-028. Vehicles previously repaired under recall 21V-028 will need to have the new remedy completed.
Campaign 23V116000 on NHTSA.gov
Power train, clutch assemblyJan 28, 2021
Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
FCA US LLC will notify owners, and dealers will add software to reduce engine torque capability when clutch assembly temperatures rise to a level that may damage the inner pressure plate, free of charge." FCA has ordered a stop sale for the affected vehicles as of February 25, 2021. Owner notification letters were mailed on March 4, 2021.
Campaign 21V028000 on NHTSA.gov
Power train, clutch assemblyMar 3, 2020
Chrysler (FCA US LLC) is recalling certain 2018-2020 Jeep Wrangler and 2020 Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
The overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Chrysler will notify owners, and dealers will reroute a wire harness and inspect the clutch system, and replace components as needed. The recall began April 30, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W12.
Campaign 20V124000 on NHTSA.gov
Seat belts, front, anchorageSep 26, 2019
Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.
A separated or severed seat belt buckle strap will result in an inoperable seat belt, increasing the risk of injury in the event of a crash.
FCA US will notify owners, and dealers will replace the driver's seat belt buckle, free of charge. Interim notices informing owners of the safety risk were mailed November 19, 2019. Owners will received a second letter and the recall began March 26, 2020. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is VA6.
Campaign 19V680000 on NHTSA.gov
EquipmentApr 23, 2019
Erwin Hymer Group USA LP dba American Fastbacks (EHGUSA-AF) is recalling certain 2018 Jeep Wrangler vehicles sold with a roof top tent installed. The top cover of the roof top tent may crack or break, possibly resulting in the cover detaching from the vehicle while moving.
If the roof top tent cover detaches from the vehicle while moving, it can create a road hazard, increasing the risk of a crash.
The remedy for this recall is still under development. The recall began May 9, 2019. Owners may contact American Fastbacks customer service at 1-844-533-7997 extension 301. Note: Vehicles in this recall are also included in recall 19V-190.
Campaign 19V320000 on NHTSA.gov
Latches/locks/linkages, doors, latchNov 8, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler four-door vehicles. The right rear passenger door latch may not be in the correct location, possibly preventing the door from latching properly.
If the right rear passenger door opens unexpectedly, it can increase the risk of injury.
Chrysler will notify owners, and dealers will repair the right rear door latch reinforcement, free of charge. The recall begin December 6, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UB6.
Campaign 18V786000 on NHTSA.gov
Structure, frame and membersSep 28, 2018
Chrysler (FCA US LLC) is recalling certain 2018-2019 Jeep Wrangler vehicles. The front track bar brackets may be improperly welded, which can cause the bracket to separate from the frame, reducing steering capability.
An unexpected reduction in steering ability, can increase the risk of a crash.
Chrysler will notify owners, and dealers will inspect and repair the track bar bracket welds, as necessary, free of charge. The recall is expected to begin November 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UA5.
Campaign 18V675000 on NHTSA.gov
Electrical system, wiring, front underhoodAug 9, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.
A vehicle stall can increase the risk of a crash.
Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.
Campaign 18V524000 on NHTSA.gov
SteeringMay 25, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The intermediate steering shaft may not have been properly welded causing a split where the external spline is formed.
If the weld seam splits, the steering wheel may lose center positioning causing a loss of steering responsiveness and increasing the risk of a crash.
Chrysler will notify owners, and dealers will inspect and, as necessary, replace the intermediate steering shaft, free of charge. The recall began June 21, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U48.
Campaign 18V343000 on NHTSA.gov
Electrical system, wiringMay 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Campaign 18V332000 on NHTSA.gov
Power train, automatic transmissionMay 1, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Dodge Charger, Durango and Challenger, Jeep Grand Cherokee and Wrangler, Chrysler 300, and RAM 1500 vehicles. An incorrect transmission park lock rod may have been installed in the transmission.
If the incorrect park lock rod is installed, the transmission may not shift into 'PARK' and keep the vehicle from moving, increasing the risk of unintended vehicle movement and the risk of a crash.
Chrysler will notify owners, and dealers will install the correct park lock rod, free of charge. The recall began June 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U43.
Campaign 18V280000 on NHTSA.gov
Structure, frame and membersApr 12, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The rear under body ladder rail may corrode, possibly reducing the strength of the rear floor pan and causing the left rear seat mount to become loose.
If the floor pan strength is reduced and/or the rear seat mount becomes loose, the rear seat may detach in a crash, increasing the risk of injury.
Chrysler will notify owners, and dealers will inspect and, as necessary, coat the interior and exterior of the driver's side rear underbody ladder rail with three-part rust protection. The recall began September 11, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U27.
Campaign 18V231000 on NHTSA.gov
Representative owner complaints
1,822 reports, newest first.
Engine, Nov 4, 2018
I HAVE A 2018 SAHARA WITH APPROX 1500 MILES ON IT. SINCE DAY ONE I HAVE FELT LIKE ITS IDLED ROUGH A CONSTANT HEAVY VIBRATION IN THE ENGINE SO MUCH SO THAT YOU CAN PHYSICALLY SEE THE PLASTIC WINDOWS OF THE SOFT TOP MOVING AND THE FRONT TIRES AND THE SEATS SHAKING. I HAVE TOOK IT TO THE DEALER TWICE BUT DEALERSHIP DIDN'T HELP !I HAD 5 WRANGLERS AND ALL MY PREVIOUS CARS DIDNT DO THIS EVERY CAR I HAVE HAD IDLES SMOOTH AND CONSISTENT ! I NEED A SOLUTION !
Steering, Nov 3, 2018
WHILE DRIVING AT 70 MILES PER HOUR, IN A STRAIGHT LINE ON A FOUR-LANE HIGHWAY, I APPROACHED A CURVE AND THE STEERING WHEEL WOULD NOT TURN. I HIT THE BRAKES AND SLOWED DOWN, AND THE STEERING WHEEL BEGAN TO RESPOND ONCE MY SPEED DROPPED BELOW 55 MILES PER HOUR. THIS HAS HAPPENED THREE TIMES.
Steering, Nov 2, 2018
MY JL CURRENTLY HAS 11,500 MILES. EVERYTHING WAS FINE DRIVING HIGHWAY SPEEDS UP TO 75 MPH UNTIL I HIT 11K MILES. ONE DAY, I WENT OVER A BRIDGE SEAM AT 75 AND THE STEERING BEGAN TO VIOLENTLY SHAKE BACK AND FORTH TO THE POINT IT WAS HARD TO CONTROL. I LET UP ON THE GAS, AND IT DIDN'T GO AWAY UNTIL I WAS DOWN TO AROUND 30 MPH. AS I WAS IN THE MIDDLE OF A BUSY MORNING COMMUTE I PUT ON MY FLASHERS TO SLOW DOWN AS I WATCHED ALL OF THE CARS BEHIND ME ALMOST CRASH TRYING TO SLOW DOWN. WHEN IT STOPPED I PULLED OVER ONE LANE WITH EVERYONE PASSING ME REALLY UPSET. LIKE I SAID, I DROVE 11K MILES WITH NO PROBLEMS AT ALL. NOW SINCE THAT HAPPENED IT HAPPENS EVERY TIME I HIT A BUMP DOING 65 MPH. I BROUGHT IT TO THE DEALER AND THEY CHECKED THE TIRE PRESSURE BUT FOUND NOTHING ELSE WRONG. I HAD READ ABOUT THE 'DEATH WOBBLE" AND ASKED ABOUT THAT BUT ALL PLAYED DUMB. ALSO, SINCE THAT HAS HAPPENED I AM FEELING THE DRIFTING IN THE STEERING WHEEL THAT OTHER ARE COMPLAINING ABOUT. THIS IS EXTREMELY UPSETTING AFTER PAYING GOOD MONEY TO NOT BE ABLE TO DRIVE SAFELY OVER 60 MPH. I AM NOT LETTING MY WIFE OR ANYONE DRIVE THE VEHICLE AND WOULD LOVE TO JUST BRING IT BACK.
Power train, Vehicle speed control, Engine, Nov 2, 2018
OPERATING VEHICLE IN 4 LOW MODE, DESCENDING A MODEST GRADE OFF ROAD, EXPERIENCED UNINTENDED VEHICLE ACCELERATION WHEN FOOT WAS OFF GAS PEDAL
Steering, Power train, Structure, Oct 31, 2018
1. THE STEERING WHEEL IS LOOSE AND VEHICLE WANDERS OFF OF THE ROAD AT >45 MPH SPEED. UNABLE TO KEEP VEHICLE ON TRAFFIC LANE. 2. THE VEHICLE STOPPED ON CITY STREET WHILE TRAVELING AT 22 MPH SPEED. CHECK ENGINE LIGHT ON AND THE TRANSMISSION LOCKED. 3. LOW BATTERY VOLTAGE (12.7V) READING WHILE RUNNING AND AT STATIONARY. *DT*JB *DT*JB
Steering, Oct 31, 2018
AT ABOUT 2400 MILES MY UNLIMITED SAHARA HAS BEGUN DOING THE JEEP DEATH WOBBLE WHEN SPEEDS ARE OVER 50 MPH AND A SMALL BUMP IS HIT I HAVE TAKEN IT TO THE DEALERSHIP TWICE AND THEY TOLD ME IT IS SAFE TO DRIVE AND THEY REPLACED THE STEERING DAMPER. THE PROBLEM IS STILL HAPPENING AND THERE IS SO MUCH PLAY IN THE STEERING WHEEL THAT I DO NOT FEEL SAFE DRIVING MY BRAND NEW JEEP ... IT IS ALL OVER THE ROAD AT HIGHWAY SPEEDS REQUIRES CONSTANT CORRECTION IN STEERING WHEN A SMALL BUMP IS HIT ON SIDE ROADS AT LOW SPEEDS CAR FEELS LIKE IT IS GOING TO FALL APART I HAVE OWNED WRANGLERS IN THE PAST AND HAVE NEVER HAD THIS HAPPEN AND NEVER FELT UNSAFE *DT *JB
Steering, Suspension, Oct 30, 2018
2018 JEEP WRANGLER UNLIMITED SAHARA WITH 9000 MILES ON IT. JUST STARTED EXPERIENCING EXTREME STEERING WHEEL SHAKING AND SUSPENSION WOBBLE AT HIGHWAY SPEEDS AFTER GOING OVER A BUMP. HAS NOW HAPPENED 6 TIMES IN THE LAST WEEK. ONLY WAY TO STOP IT IS TO SLOW DOWN OR STOP.
Steering, Oct 29, 2018
WHILE DRIVING AT SLOW OR HIGH SPEED IT SEEMS THERE IS A "DEAD SPOT" IN THE STEERING, ABOUT AN INCH. WHEN I TURN I HAVE TO TURN BACK THE OTHER WAY WAY TO CORRECT. ALWAYS TURNING THE WHEEL FROM ONE SIDE TO THE OTHER. EITHER THERE IS A 'DEAD SPOT" OR THE STEERING IS TOO SLOW TO RESPOND.
Structure, Oct 29, 2018
BRAND NEW 2018 JEEP WRANGLER JLU, ONLY 400 MILE, DUE TO THE RECENT RECALL ON THE TRACK BARD WELD ISSUE, I WENT OVER THE VEHICLE AND INSPECTED THE WELDS ON OTHER AREAS OF MY VEHICLE AND NOTICE THAT THE WELDING ON THE REAR LOWER CONTROL ARM BRACKET WAS NOT PROPERLY WELDED. THE WELD WAS MOSTLY ON THE FRAME RATHER THAN ON THE SEAM BETWEEN THE FRAME AND THE CONTROL ARM BRACKET, BY COMPARING THE DRIVER SIDE REAR LOWER CONTROL ARM BRACKET, IT WAS CLEARLY APPARENT THAT THERE WAS A WELDING ERROR. ADDITIONALLY, (REFER TO ATTACHED PDF DOCUMENT) THE ROBOTIC WELDER NOT ONLY MISSED THE SEAM BUT STOPPED WELDING AFTER ABOUT 1.5" (UP TO THE WHITE LINE MARKED BY QC) THE A PERSON WELDED FROM RIGHT TO LEFT (UP TO THE WHITE LINE WHERE THE ROBOT STOPPED) BUT ALSO MISSED THE SEAM AND WELDED MOSTLY ON THE FRAME. CHRYSLER HAD TO HAVE KNOWN ABOUT THE ISSUE BECAUSE A PERSON DID WELD WHERE THE ROBOT STOPPED. HOWEVER, THE IMPROPER WELDING WAS PERFORMED AND THIS ISSUE CAN POTENTIALLY CAUSE A FATAL ACCIDENT BEING THAT THIS VEHICLE IS A OFF-ROAD CAPABLE VEHICLE AND UNLIKE REGULAR VEHICLE, THIS VEHICLE WILL MORE LIKELY BE USED IN EXTREME CONDITIONS FURTHER PLACING STRESS ON THE IMPROPERLLY WELDED COMPONENTS.
Steering, Oct 29, 2018
VEHICLES TIRES BEGIN TO SHAKE VIOLENTLY AT SPEEDS IN THE 70-75 MPH RANGE ON THE HIGHWAY. CONDITION OCCURS AFTER HITTING A SMALL BUMP ON THE HIGHWAY. THE CONDITION BECOMES SO VIOLENT, I HAVE TO SLOW THE VEHICLE FROM 70+ MPH TO ABOUT 40 MPH TO STOP THE SHAKING. THIS CONDITION OCCURRED DURING RUSH HOUR IN HEAVY TRAFFIC ON I-696. MY WIFE TOOK THE VEHICLE TO THE DEALERSHIP ON THURSDAY OCTOBER 25TH. THE DEALER TOLD HER THEY WOULD HAVE TO REPLACE THE STEERING DAMPER AND THAT THE PART WAS ON BACK ORDER. THEY SAID IT COULD TAKE A MONTH TO GET THE PART AND THAT THE VEHICLE WAS "SAFE" TO DRIVE. I DROVE THE JEEP TO WORK ON FRIDAY OCT 26TH. ON THE WAY HOME, TO CONDITION OCCURRED ON I-696 WHILE I WAS TRAVELING 70+ MPH IN RUSH HOUR TRAFFIC. I HAD TO SLOW THE VEHICLE TO APPROXIMATELY 40 MPH IN THE CENTER LANE ON THE HIGHWAY BEFORE THE SHAKING ENDED. I ALMOST CAUSED AN ACCIDENT ON THE HIGHWAY. I AM AN ENGINEER AND HAVE WORKED IN THE AUTO INDUSTRY FOR ABOUT 30 YEARS. I HAVE BEEN INVOLVED IN FIELD ACTIONS, CAMPAIGNS AND RECALLS. THIS VEHICLE IS NOT SAFE AND SHOULD BE GROUNDED AND FIXED. I DID SOME RESEARCH OVER THE WEEKEND AND THE CONDITION IS KNOWN AS "DEATH WOBBLE". IT IS FAIRLY COMMON. OUR VEHICLE IS A STOCK 2018 JEEP WRANGLER WITH NO MODIFICATIONS TO THE SUSPENSION. THE DEALERSHIP IS SUBURBAN JEEP LOCATED IN FARMINGTON HILLS, MI ON GRAND RIVER & 10 MILE. THE DEALER SHOULD NOT HAVE SENT MY WIFE HOME TELLING HER THE VEHICLE IS SAFE. THIS VEHICLE IS NOT SAFE AND SHOULD BE GROUNDED IMMEDIATELY. LOOKING FOR SUPPORT FROM NHTSA TO CORRECT THIS ISSUE. THIS CONDITION HAS OCCURRED TWICE WHILE I WAS DRIVING AND ONCE WITH MY WIFE DRIVING OUR 9 YEAR OLD SON. PLEASE HELP.
Steering, Oct 28, 2018
JEEP WANDERS ALL OVER THE ROAD. THE WANDERING IS MORE PRONOUNCED AT HIGHER SPEED. THE STEERING IS SO BAD MY WIFE REFUSES TO DRIVE THE VEHICLE. I CAN TOLERATE IT ONLY BECAUSE I KNOW IT CAN BE ADDRESSED WITH LONGER CONTROL ARMS WHEN I MODIFY THE VEHICLE. I DON'T BELIEVE THE CASTER ANGLE SPEC FOR THE RUBICON MODEL IS OPTIMAL.
Steering, Oct 27, 2018
VEHICLE IS UNSTABLE AT ALL SPEEDS. JEEP IS ALMOST IMPOSSIBLE TO KEEP IN DRIVE LANE AND DARTS BACK AND FORTH. I HAVE TO KEEP BOTH HANDS ON THE STEERING WHEEL AT ALL TIMES TO CORRECT DRIFTING AND STAY OUT OF THE DEAD SPOT IN THE CENTER OF THE STEERING WHEEL. I DO NOT FEEL SAFE DRIVING THIS VEHICLE ON PAVED ROADS.
Steering, Oct 27, 2018
LOOSE STEERING ALL THE TIME. AND THEN AT HIGH SPEEDS ON THE HIGHWAY THE STEERING WHEEL LOCKS AND THE STRAIGHT POSITION.
Steering, Electrical system, Electronic stability control (ESC), Oct 26, 2018
INTERMITTENT LOSS OF POWER STEERING AND/OR SEIZING. UPON DRIVING TO EXIT HIGHWAY AND GET TO DEALERSHIP ENGINE INDICATOR LIGHT CAME ON AND EVENTUALLY JEEP STOPPED DEAD WHILE DRIVING. COULD NOT BE PUT IN NEUTRAL TO MOVE OFF OF ROAD AND WOULD NOT RESTART AT ALL.*DT CONSUMER STATED AUTO WINDOWS WOULD NOT WORK ALTHOUGH THE CHILD LOCKS WERE DISENGAGED. RECEIVED RECALLED OCT. 5TH 2018 JUST AFTER CONSUMER PURCHASED THE VEHICLE WITH MILAGE OF LESS THAN 1200. UPDATED 1/30/18*JB
Power train, Oct 25, 2018
I ENTERED A PARKING SPACE AND WAS NOT WITHIN THE LINES. I BACKED UP ABOUT 2 FEET AND FELT A SUDDEN STOP AND 'CLUNK.' I COULD NOT MOVE THE SHIFTER AT ALL. THE DASH DISPLAY SAID 'PARK LOCK.' IT INSTRUCTED ME TO TURN THE CAR OF AND THEN PUT IT BACK IN GEAR. AFTER 3 ATTEMPTS TO DO THAT (I MAY HAVE BEEN RUSHED THE FIRST 2 TIMES) THE I WAS ABLE TO PUT IT IN GEAR. THERE ARE FEWER THAN 500 MILES ON THIS NEW VEHICLE. IT HASN'T HAPENED AGAIN, BUT THIS SEEMS VERY DANGEROUS. I HAVE AN APPOINTMENT TO TAKE IT TO THE DEALER.
Other or unspecified, Oct 25, 2018
JEEP FRAME WELDS HAVE A LOT OF POROSITY AND SLAG. MANY OF THE WELDS ALL OVER THE FRAME DO NOT APPEAR TO BE COMPLETE AND LOOK UNSAFE. NOTHING HAS BEEN DONE TO THE JEEP AND WAS THIS WAY FROM THE FACTORY. VERY CONCERNED ABOUT CRASH SAFETY STRENGTH AND LONGEVITY IF WELDS START TO RUST AND DETERIORATE.
Steering, Oct 25, 2018
VEHICLE IS UNBELIEVABLY UNSTABLE WHILE DRIVING. DARTS BACK AND FORTH AND IS ALMOST IMPOSSIBLE TO KEEP IN SINGLE LANE. MUST KEEP BOTH HANDS ON WHEEL AT ALL TIMES AND BE 100% FOCUSED ON KEEPING VEHICLE IN SINGLE LANE. CANNOT BE CONSIDERED SAFE.
Steering, Suspension, Oct 24, 2018
MY JEEP WRANGLER JL WITH UNDER 7000 MILES BEGINS TO SHAKE VIOLENTLY AT HWY SPEEDS BETWEEN 50 -65. THIS VIOLENT FRONT END SHAKING, SHAKES THE WHOLE JEEP MAKING IT DIFFICULT TO STEER AND CONTROL. SHAKING WILL STOP ONCE YOU SLOW DOWN TO A SLOW SPEED OR COME TO A COMPLETE STOP. IT WAS SO BAD MY CHILDREN, WHO WERE IN JEEP FOR ONE INSTANCE, WERE SCARED AND VISABLELY SHAKEN FROM THE EXPERIENCE. THIS HAD NOW HAPPEN 5 TIMES IN A THE SPAN OF A WEEK. *DT CONSUMER STATED TIRE WAS REPLACED BUT VEHICLE WAS STILL SHAKING. UPDATED 12/13/18*JB
Structure, Oct 24, 2018
TL* THE CONTACT OWNS A 2018 JEEP WRANGLER. THE CONTACT STATED THAT THE SUBFRAME WELDING WAS RUSTED, CORRODED, MISALIGNED, AND DID NOT MEET THE MANUFACTURER'S SPECIFICATIONS RELATED TO SPACING. THE VEHICLE WAS TAKEN TO THE LOCAL DEALER (BENNETT JEEP, 149 HWY 40 EAST, KINGSLAND, GA) TO BE DIAGNOSED, BUT THE CAUSE OF THE FAILURES COULD NOT BE DETERMINED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED, BUT NO SOLUTION WAS OFFERED. THE FAILURE MILEAGE WAS 5,000.
Steering, Oct 24, 2018
WHILE DRIVING THE STEERING WHEEL HAS A DEAL SPOT AND THE TRUCK WONDERS ALL OF THE ROAD. ON COLD DAYS DURING INITIAL START UP, BELOW 40 DEGREES, THE TRUCK LOSES ITS POWER STEERING FUNCTION AND IT DOESNT RETURN TILL AFTER TRUCK HAS WARMED UP.
Steering, Oct 23, 2018
STEERING SEEMS TO LOSE POWER ASSIST AND ALMOST LOCK UP AT HIGHWAY SPEEDS HAS HAPPENED REPEATEDLY. EXTREMELY DANGEROUS. THERE SEEMS TO BE LOTS OF REFERENCE TO THIS ON THE INTERNET FROM OTHER 2018 JL WRANGLER OWNERS.
Steering, Oct 23, 2018
THE STEERING HAS A DEAD SPOT IN THE CENTER WHICH CAUSES WANDERING IN THE LANE AND OVER CORRECTION AT 40 MPH AND UP TO HIGHWAY SPEEDS. THIS CAUSES UNSAFE LANE KEEPING ON COUNTRY ROADS AS WELL AS HIGHWAY AND INTERSTATE TRAVEL. BOTH MY WIFE AND I HAVE NEARLY SIDE SWIPED VEHICLES AND CLOSE CALLS IN ONCOMING TRAFFIC. THE DEALER IN MY LOCATION SAYS IT'S NORMAL BEHAVIOR BUT THE ABILITY TO STAY IN MY LANE IS NOT SAFE IN ANY WAY.
Structure, Engine, Oct 23, 2018
2018 JEEP JL (ALL WHITE) HAS PAINT TURNING YELLOW FROM EXCESS HEAT IN THE ENGINE AREA. JEEP HAS LESS THAN 300 MILES ON IT. AREAS AFFECTED INCLUDE FRONT GRILL, RIGHT FRONT FENDER. PRIMARILY ON DRIVER'S SIDE. NOT AN ISOLATED INCIDENT - SEE HTTPS://WWW.JLWRANGLERFORUMS.COM/FORUM/THREADS/BRIGHT-WHITE-GRILLE-TURNING-YELLOW.6394/ .
Steering, Oct 23, 2018
VEHICLE WANDERS ON THE ROAD, PULLS TO ONE SIDE OR THE OTHER AND OVER CORRECTS WHEN YOU TRY TO STRAIGHTEN IT OUT ON THE ROAD WHICH AT HIGHWAY SPEEDS CAN LEAD TO A WOBBLE FROM SIDE TO SIDE. IT HAS BEEN IN THE SHOP AT LEAST 4 TIMES AND CHRYSLER CORP STATES IT IS "RUNNING AS DESIGNED". STATEMENT FROM FIELD TECHNICIAN IN RESPONSE TO FINAL OPPORTUNITY TO REPAIR LETTER: "VEHICLE OPERATING AS DESIGNED AND CONSISTANT WITH ALL OTHER 2018 JL JEEP RUBICON WRANGLERS WITH BF GOODRICH ALL -TERRAIN TA TIRES. THE TREAD AND SIDEWALL DESIGN OF THIS TIRE CONTRIBUTES TO THE CONDITION DESCRIBED BY THE CUSTOMER. NO VEHICLE REPAIRS ARE NEEDED AT THIS TIME."
Power train, Oct 23, 2018
DRIVE TRAIN VIBRATION MOST NOTICEABLE BETWEEN 59 - 64 MPH. VIBRATION IN STEERING WHEEL, DRIVER AND PASSENGER FRONT SEATS, FLOOR PANS. 10/3 - 10/8/18 DEALER INSPECTED ENTIRE VEHICLE, BALANCED, ROAD FORCE TESTED TIRES FOUND ALL WITHIN SPEC AND BALANCED WITH NO INDEXING REQUIRED. IN ADDITION TO EXTENSIVE ROAD TESTING, EVALUATION, THE SERVICE DEPARTMENT TEMPORARILY REPLACED 2018 JLU RUBICON WHEELS/TIRES WITH WHEELS/ROAD FRIENDLY TIRES FROM OTHER WRANGLER MODEL AND DRIVE TRAIN VIBRATION WAS STILL PRESENT. DEALER SERVICE SHOP FOREMAN INDICATED TRANSMISSION, TORQUE CONVERTER OR DRIVE SHAFT OUT OF BALANCE BUT NEEDED GUIDANCE FROM CHRYSLER ENGINEERING ON NEXT STEPS AND PROPOSED RESOLUTION. MET WITH CHRYSLER ENGINEERING AT DEALERSHIP SERVICE DEPARTMENT 10/22/18 AND CHRYSLER ENGINEER STATED IT'S THE TIRES AND AFTER ANOTHER BALANCE AND ROAD FORCE TEST INFORMED ME EVERYTHING WAS WITHIN SPECIFICATIONS AND THEY ROTATED TIRES FRONT TO BACK. NO CHANGES TO PROBLEM AND VIBRATION STILL EXISTS. I'VE HAD THE TIRES/WHEELS BALANCED AND ROAD FORCE TESTED BY AN INDEPENDENT 3RD PARTY AND NOW TWICE BY THE DEALERSHIP. VEHICLE IS LESS THAN 2 MONTHS OLD AND 1300 MILES.